Nissan X-Trail 32. Instruction — part 2068
TM-230
< PRECAUTION >
[CVT: RE0F10D]
PRECAUTIONS
CAUTION:
While waiting, never operate the vehicle such as locking, opening, and closing doors. Violation of
this caution results in the activation of ACC power supply according to the Auto ACC function.
5.
Remove 12V battery terminal.
CAUTION:
After installing 12V battery, always check self-diagnosis results of all ECUs and erase DTC.
INSTRUCTION 2 (FOR VEHICLES PARKED BY IGNITION SWITCH OFF)
1.
Unlock the door with intelligent key or remote keyless entry.
NOTE:
At this moment, ACC power is supplied.
2.
Open the driver side door.
3.
Open the hood.
4.
Close the driver side door.
5.
Wait at least 3 minutes.
CAUTION:
While waiting, never operate the vehicle such as locking, opening, and closing doors. Violation of
this caution results in the activation of ACC power supply according to the Auto ACC function.
6.
Remove 12V battery terminal.
CAUTION:
After installing 12V battery, always check self-diagnosis results of all ECUs and erase DTC.
Precaution for TCM and Transaxle Assembly Replacement
INFOID:0000000010622418
CAUTION:
• To replace TCM, refer to
.
• To replace transaxle assembly, refer to
• To replace TCM and transaxle assembly simultaneously, refer to
General Precautions
INFOID:0000000010622419
• Turn ignition switch OFF and disconnect the battery cable
from the negative terminal before connecting or disconnect-
ing the CVT assembly harness connector. Because battery
voltage is applied to TCM even if ignition switch is turned
OFF.
• When connecting or disconnecting pin connectors into or
from TCM, do not damage pin terminals (bend or break).
Check that there are not any bends or breaks on TCM pin ter-
minal, when connecting pin connectors.
K9K engine
: 4 minutes
M9R engine
: 4 minutes
R9M engine
: 4 minutes
V9X engine
: 4 minutes
SEF289H
AAT470A
PRECAUTIONS
TM-231
< PRECAUTION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• Perform TCM input/output signal inspection and check
whether TCM functions normally or not before replacing TCM.
Refer to
• Perform “DTC (Diagnostic Trouble Code) CONFIRMATION
PROCEDURE”.
If the repair is completed DTC should not be displayed in the
“DTC CONFIRMATION PROCEDURE”.
• Always use the specified brand of CVT fluid. Refer to
MA-23, "Fluids and Lubricants"
• Use lint-free paper not cloth rags during work.
• Dispose of the waste oil using the methods prescribed by law, ordinance, etc. after replacing the CVT fluid.
On Board Diagnosis (OBD) System of CVT and Engine
INFOID:0000000010622420
The TCM and ECM have an on board diagnostic system. It will light up the malfunction indicator lamp (MIL) to
warn the driver of a malfunction causing emission deterioration.
CAUTION:
• Be sure to turn the ignition switch OFF and disconnect the battery cable from the negative terminal
before any repair or inspection work. The open/short circuit of related switches, sensors, solenoid
valves, etc. will cause the MIL to light up.
• Be sure to connect and lock the connectors securely after work. A loose (unlocked) connector will
cause the MIL to light up due to an open circuit. (Be sure the connector is free from water, grease,
dirt, bent terminals, etc.)
• Be sure to route and secure the harnesses properly after work. Interference of the harness with a
bracket, etc. may cause the MIL to light up due to a short circuit.
• Be sure to connect rubber tubes properly after work. A misconnected or disconnected rubber tube
may cause the MIL to light up due to a malfunction of the EGR system or fuel injection system, etc.
• Be sure to erase the unnecessary malfunction information (repairs completed) from the TCM and
ECM before returning the vehicle to the customer.
Removal and Installation Procedure for CVT Unit Connector
INFOID:0000000010622421
REMOVAL
MEF040DA
JSBIA1315ZZ
TM-232
< PRECAUTION >
[CVT: RE0F10D]
PRECAUTIONS
• Rotate bayonet ring
counterclockwise. Pull out CVT unit har-
ness connector
upward and remove it.
INSTALLATION
1.
Align marking
on CVT unit harness connector terminal with
marking
on bayonet ring. Insert CVT unit harness connector.
2.
Rotate bayonet ring clockwise.
3.
Rotate bayonet ring clockwise until marking
on CVT unit har-
ness connector terminal body is aligned with the slit
on bayo-
net ring as shown in the figure (correctly fitting condition).
CAUTION:
• Securely align marking
on CVT unit harness connector
terminal body with bayonet ring slit
. Then, be careful
not to make a half fit condition as shown in the figure.
• Never mistake the slit of bayonet ring for other dent por-
tion.
SCIA6685J
JPDIA0294ZZ
JPDIA0295ZZ
JPDIA0296ZZ
PREPARATION
TM-233
< PREPARATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000010622422
*: The O-ring as a unit part is set as a SST.
Commercial Service Tools
INFOID:0000000010622423
Tool number
Tool name
Description
1.
KV311039S0
Charging pipe set
2.
KV31103920*
O-ring
CVT fluid changing and adjustment
KV38107900
Protector
a: 32 mm (1.26 in) dia.
Installing drive shaft
JSDIA1844ZZ
PDIA1183J
Tool number
Tool name
Description
Power tool
Loosening nuts and bolts
Lint-free paper
Cleaning transaxle
Oil seal remover
Removing each oil seal
PBIC0190E
JSDIA4746ZZ
JSDIA4998ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст