Nissan X-Trail 32. Instruction — part 640
REAR DOOR
DLK-901
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
4.
Disengage fixing pawl on front upper end of rear door weather-strip using a remover tool (A), and then
remove weather-strip clip.
5.
Remove rear fixing clips from weather-strip.
6.
Disengage fixing pawl on rear upper end of rear door weather-strip using a remover tool (A), and then
remove weather-strip clip.
7.
Remove door check link mounting bolt of vehicle body side.
8.
Remove rear door weather-strip from rear door panel.
INSTALLATION
Install in the reverse order of removal.
: Pawl
JMKIB3515ZZ
JMKIB3516ZZ
: Pawl
JMKIB3517ZZ
DLK-902
< REMOVAL AND INSTALLATION >
[TYPE 4]
BACK DOOR
BACK DOOR
Exploded View
INFOID:0000000010728697
BACK DOOR ASSEMBLY
BACK DOOR ASSEMBLY : Removal and Installation
INFOID:0000000010728698
CAUTION:
• Back door is made of resin. Never apply strong force to it, and be careful to prevent contact with oil.
• Perform work with 2 workers, because of its heavy weight.
• Use protective tape or shop cloth to protect from damage during removal and installation.
Back door hinge
Back door stay
Back door weather-strip
Bumper rubber
Wedge bracket
Back door wedge
Back door striker
TORX bolt
Back door panel
Plug
Stud ball
Back door damper
: Center mark
: Seam
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Body grease
,
: Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIB2695GB
BACK DOOR
DLK-903
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOVAL
1.
Remove headlining. Refer to
INT-37, "Removal and Installation"
2.
Disconnect back door harness connectors
,
and
, and
then remove harness fixing clips
.
3.
Disconnect harness connector
, and then remove harness fix-
ing clips
.
4.
Remove grommet
from roof panel
, and then pull out back
door harness from vehicle body.
5.
Remove air tube
from tube clip
, and then disconnect tube
joint connector
and air tube
(with around view monitor).
: Vehicle front
JMKIB3115ZZ
: Vehicle front
JMKIB3116ZZ
JMKIB3117ZZ
: Vehicle front
JMKIB3118ZZ
DLK-904
< REMOVAL AND INSTALLATION >
[TYPE 4]
BACK DOOR
6.
Remove tube grommet
from roof panel
, and then pull out
air tube from vehicle body.
7.
Disconnect rear washer tube A and rear washer tube B. Refer to
.
8.
Disconnect rear view camera washer tube (with around view monitor). Refer to
.
9.
Remove tube grommet
from roof panel
, and then pull out
rear washer tube B and rear camera washer tube from vehicle
body.
10. Support back door with the proper material to prevent it from falling.
WARNING:
Bodily injury may occur if no supporting rod is holding the back door open when removing the
back door stay.
11. Remove back door stay from back door. Refer to
DLK-907, "BACK DOOR STAY : Removal and Installa-
12. Remove back door hinge mounting nuts of back door and remove back door assembly.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• After installation, perform the fitting adjustment. Refer to
DLK-905, "BACK DOOR ASSEMBLY :
• After installation, check whether harness is not pinched. If harness is pinched, pull harness down-
ward lightly.
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
• After installation, check that door opens and closes normally. Refer to
BACK DOOR ASSEMBLY : Inspection
INFOID:0000000010728699
1.
Open and close the back door. Check that door hinge rotation portion moves smoothly.
JMKIB3119ZZ
JMKIB3120ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст