Nissan X-Trail 32. Instruction — part 2115
TM-418
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
AIR BREATHER
QR25DE : Exploded View
INFOID:0000000010622603
QR25DE : Removal and Installation
INFOID:0000000010622604
REMOVAL
1.
Remove air duct 1 and air duct 2. Refer to
EM-175, "Removal and Installation"
.
2.
Remove air breather hose from transaxle assembly.
INSTALLATION
Note the followings and installation is in the reverse order of removal.
CAUTION:
• Never bend the air breather hose to prevent damage to the hose.
• Insert air breather hose to the end of air breather cap.
• Insert air breather hose
to air breather tube
all the way to
the curve of the tube.
• Insert air breather hose to air breather tube so that the paint
mark
is facing upward.
Air breather cap
Air breather hose
Air breather tube
Transaxle assembly
JSDIA5140ZZ
ALDIA0501ZZ
OIL PAN
TM-419
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OIL PAN
Exploded View
INFOID:0000000010622605
Removal and Installation
INFOID:0000000010622606
REMOVAL
1.
Remove the engine under cover. Refer to
EXT-40, "ENGINE UNDER COVER : Removal and Installation"
.
2.
Remove the drain plug
from oil pan and drain the CVT fluid.
Transaxle assembly
Oil pan gasket
Oil pan
Drain plug
Drain plug gasket
Magnet
Overflow plug
O-ring
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Apply CVT fluid
JSDIA4194GB
JSDIA5205ZZ
TM-420
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
OIL PAN
3.
Remove the drain plug gasket
.
4.
Remove the oil pan bolts (
) and remove the oil pan and oil pan
gasket.
5.
Remove the oil pan gasket
from the oil pan.
6.
Remove the magnets
from the oil pan.
INSTALLATION
Note the followings and installation is in the reverse order of removal.
CAUTION:
• Never reuse oil pan gasket.
• Never reuse drain plug gasket.
• Completely clean the iron powder from the magnet area of oil pan and the magnets.
• Install the oil pan to the transaxle case with the following procedure.
1.
Install the oil pan gasket to the oil pan.
CAUTION:
Completely wipe out any moisture, oil, and old gasket from the oil pan gasket surface and bolt
hole of oil pan and transaxle case.
2.
Install the oil pan assembly to the transaxle case and temporarily tighten the oil pan bolt.
JSDIA5206ZZ
: Vehicle front
JSDIA5207ZZ
JSDIA5208ZZ
JSDIA5209ZZ
OIL PAN
TM-421
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
3.
Tighten the oil pan bolts in the order shown to the specified
torque.
4.
Tighten the oil pan bolts again clockwise from (1) shown to the
specified torque.
• Fill ATF after installation. Refer to
.
Inspection
INFOID:0000000010622607
INSPECTION AFTER REMOVAL
Check oil pan for foreign material.
• If a large amount of worn material is found, clutch plate may be worn.
• If iron powder is found, bearings, gears, or clutch plates may be worn.
• If aluminum powder is found, bushing may be worn, or chips or burrs of aluminum casting parts may enter.
Check points where wear is found in all cases.
INSPECTION AFTER INSTALLATION
Check the CVT fluid leakage. Refer to
: Vehicle front
JSDIA5211ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст