Nissan X-Trail 32. Instruction — part 2116
TM-422
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
INPUT SPEED SENSOR
INPUT SPEED SENSOR
MR20DD
MR20DD : Exploded View
INFOID:0000000010622608
MR20DD : Removal and Installation
INFOID:0000000010622609
REMOVAL
1.
Turn ignition switch OFF.
2.
Remove air duct 1. Refer to
.
3.
Disconnect input speed sensor connector
.
Transaxle assembly
O-ring
Input speed sensor
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Apply CVT fluid
JSDIA5264GB
JSDIA5194ZZ
INPUT SPEED SENSOR
TM-423
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4.
Remove mounting bolt (
) and remove input speed sensor
from transaxle assembly.
5.
Remove O-ring
from input speed sensor.
INSTALLATION
Note the followings and installation is in the reverse order of removal.
CAUTION:
• Never reuse O-ring.
• Apply CVT fluid to the O-ring.
MR20DD : Inspection and Adjustment
INFOID:0000000010622610
INSPECTION AFTER INSTALLATION
Start the engine and check visually that there is no leakage of CVT fluid.
ADJUSTMENT AFTER INSTALLATION
If CVT fluid leaks during work, adjust the CVT fluid level. Refer to
.
QR25DE
QR25DE : Exploded View
INFOID:0000000010622611
JSDIA5195ZZ
JSDIA5196ZZ
JSDIA4131GB
TM-424
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
INPUT SPEED SENSOR
QR25DE : Removal and Installation
INFOID:0000000010622612
REMOVAL
1.
Turn ignition switch OFF.
2.
Remove the starter motor. Refer to
STR-34, "QR25DE : Removal and Installation"
.
3.
Disconnect the input speed sensor harness connector.
4.
Remove the input speed sensor bolt (
) and remove the input
speed sensor
.
5.
Remove the O-ring
from the input speed sensor.
INSTALLATION
Note the followings and installation is in the reverse order of removal.
CAUTION:
• Never reuse O-ring.
• Apply CVT fluid to the O-ring.
QR25DE : Inspection and Adjustment
INFOID:0000000010622613
INSPECTION AFTER INSTALLATION
Start the engine and check visually that there is no leakage of CVT fluid.
ADJUSTMENT AFTER INSTALLATION
If CVT fluid leaks during work, adjust the CVT fluid level. Refer to
.
Input speed sensor
O-ring
Transaxle assembly
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Apply CVT fluid
JSDIA5427ZZ
JSDIA5199ZZ
PRIMARY SPEED SENSOR
TM-425
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
PRIMARY SPEED SENSOR
Exploded View
INFOID:0000000010622614
Removal and Installation
INFOID:0000000010622615
REMOVAL
1.
Turn ignition switch OFF.
2.
Disconnect the primary speed connector
.
3.
Remove the primary speed sensor bolt (
) and remove the pri-
mary speed sensor
.
Transaxle assembly
O-ring
Primary speed sensor
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Apply CVT fluid
JSDIA5141GB
JSDIA5197ZZ
JSDIA5198ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст