Nissan X-Trail 32. Instruction — part 1108
EXHAUST MANIFOLD
EM-329
< REMOVAL AND INSTALLATION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Loosen mounting nuts in the reverse order as shown in the fig-
ure.
6.
Remove exhaust manifold gasket.
CAUTION:
Cover engine openings to avoid entry of foreign materials.
INSTALLATION
CAUTION:
• Clean each joint surface before installation.
• Replace exhaust manifold stud if loosened.
1.
Install gasket to cylinder head as shown in the figure.
2.
Install exhaust manifold.
• Tighten the mounting nuts in two steps separately in numerical
order as shown in the figure.
3.
Install in the reverse order of removal, for the rest of parts.
Inspection
INFOID:0000000010784327
INSPECTION AFTER REMOVAL
Surface Distortion
• Check the surface distortion of the exhaust manifold mating surface with a straightedge and a feeler gauge.
• If it exceeds the standard, replace exhaust manifold.
INSPECTION AFTER INSTALLATION
Start engine and raise engine speed to check no exhaust emission leaks.
: Vehicle front
E1BIA0581ZZ
: Engine upper
E1BIA0583ZZ
: Vehicle front
1st step: 15.0 N·m (1.5 kg-m, 11 ft-lb)
2nd step: 30.0 N·m (3.1 kg-m, 22 ft-lb)
E1BIA0581ZZ
Standard
: Refer to
EM-330
< REMOVAL AND INSTALLATION >
[R9M]
OIL PAN (LOWER)
OIL PAN (LOWER)
Exploded View
INFOID:0000000010784328
Removal and Installation
INFOID:0000000010784329
REMOVAL
1.
Remove engine under cover. Refer to
EXT-39, "ENGINE UNDER COVER : Exploded View"
2.
Drain engine oil. Refer to
.
CAUTION:
Perform this step when engine is cold.
3.
Remove oil pan (lower) with the following procedure:
Oil pan (upper)
Oil pan (lower)
Drain plug washer
Oil pan drain plug
Oil level sensor
Comply with the installation proce-
dure when tightening. Refer to
380, "Removal and Installation"
Comply with the installation proce-
dure when tightening. Refer to
330, "Removal and Installation"
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
: Sealing point
JPBIA6951GB
OIL PAN (LOWER)
EM-331
< REMOVAL AND INSTALLATION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
a.
Loosen mounting bolts in reverse order shown in the figure.
b.
Insert the seal cutter [SST:KV10111100 ( — )] (A) between oil
pan (upper) and oil pan (lower). Slide tool by tapping on the side
of the tool with a hammer.
CAUTION:
• Be careful not to damage mating surface.
• Never insert screwdriver, or oil pan flange will be
deformed.
c.
Remove oil pan (lower).
4.
Remove oil strainer. Refer to
.
INSTALLATION
1.
Install oil strainer. Refer to
2.
Install oil pan (lower) with the following procedure:
a.
Use a scraper (A) to remove old liquid gasket from mating sur-
faces.
CAUTION:
Never scratch or damage the mating surfaces when clean-
ing off old liquid gasket.
• Remove old liquid gasket from the bolt holes and threads.
b.
Apply a continuous bead of liquid gasket with the tube presser
(commercial service tool) as shown in the figure.
Use Genuine Liquid Gasket or equivalent
CAUTION:
Attaching should be done within 5 minutes after coating.
E1BIA0582ZZ
JPBIA0276ZZ
JPBIA0025ZZ
: Oil pan (lower)
: 3.0 - 7.0 mm (0.118 - 0.276 in)
: Engine front
JPBIA6982ZZ
EM-332
< REMOVAL AND INSTALLATION >
[R9M]
OIL PAN (LOWER)
c.
Tighten mounting bolts in two steps separately in numerical
order as shown in the figure.
3.
Install in the reverse order of removal, for the rest of parts.
NOTE:
At least 30 minutes after oil pan is installed, pour engine oil.
Inspection
INFOID:0000000010784330
INSPECTION AFTER REMOVAL
Clean oil strainer if any object attached.
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level and adjust engine oil. Refer to
.
2.
Start engine, and check there is no leak of engine oil.
3.
Stop engine and wait for 10 minutes.
4.
Check the engine oil level again. Refer to
1st step: 5.0 N·m (0.51 kg-m, 44 in-lb)
2nd step: 12.0 N·m (1.2 kg-m, 9 ft-lb)
E1BIA0582ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст