Nissan X-Trail 32. Instruction — part 667
TRANSFER COVER OIL SEAL
DLN-79
< REMOVAL AND INSTALLATION >
[TRANSFER: TY21C]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
4.
Perform inspection after installation. Refer to
MR20DD : Inspection
INFOID:0000000010992035
INSPECTION AFTER INSTALLATION
Check oil level and transfer for oil leakage. Refer to
QR25DE
QR25DE : Removal and Installation
INFOID:0000000011001966
NOTE:
• Replacement on vehicle may cause damage to transfer cover, and may cause a transfer oil leak.
• If transfer cover oil seal requires replacement, remove transfer assembly from the vehicle before replacing
transfer cover oil seal. Refer to
DLN-80
< UNIT REMOVAL AND INSTALLATION >
[TRANSFER: TY21C]
TRANSFER ASSEMBLY
UNIT REMOVAL AND INSTALLATION
TRANSFER ASSEMBLY
MR20DD
MR20DD : Exploded View
INFOID:0000000011002856
MR20DD : Removal and Installation
INFOID:0000000011002857
REMOVAL
1.
Remove exhaust front tube. Refer to
EX-6, "Removal and Installation"
2.
Remove front drive shaft (RH). Refer to
FAX-101, "MR20DD : Removal and Installation"
CAUTION:
Oil may leak from the opening. Use cap and/or plug to prevent leakage.
3.
Remove propeller shaft from transfer assembly. Refer to
DLN-214, "Removal and Installation"
.
CAUTION:
The joint of propeller shaft must be handled with care.
4.
Remove transfer gusset
.
5.
Remove transfer assembly from transaxle assembly.
CAUTION:
• Never damage ring gear shaft.
• Be careful when removing transfer assembly form the
vehicle because it is heavy.
INSTALLATION
Note the following, and install in the reverse order of removal.
Transfer gusset
Transfer assembly
: N·m (kg-m, ft-lb)
*: Apply anti-corrosion oil.
JSDIA5353GB
JSDIA5358ZZ
TRANSFER ASSEMBLY
DLN-81
< UNIT REMOVAL AND INSTALLATION >
[TRANSFER: TY21C]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• When installing the transfer to the transaxle, install the mounting
bolts following the standard below, tighten bolts to the specified
torque. For each tightening torque, refer to
.
CAUTION:
• Apply anti-corrosion oil to the thread and seat of mounting bolts.
• Never damage O-ring of transfer.
• For mounting bolts of transfer gusset, temporarily tightening the engine side bolt first. After this, tighten bolts
to the specified torque in the order from transfer side bolt to engine side bolt. For tightening torque, refer to
DLN-81, "QR25DE : Exploded View"
.
• Perform inspection after installation. Refer to
.
MR20DD : Inspection
INFOID:0000000011002858
INSPECTION AFTER INSTALLATION
When oil leaks while removing/installing transfer assembly, check oil level after the installation. Refer to
QR25DE
QR25DE : Exploded View
INFOID:0000000011002859
QR25DE : Removal and Installation
INFOID:0000000011002860
REMOVAL
1.
Remove front drive shaft (RH). Refer to
FAX-113, "QR25DE : Removal and Installation"
CAUTION:
Oil may leak from the opening. Use cap and/or plug to prevent leakage.
2.
Remove front suspension member. Refer to
FSU-22, "Removal and Installation"
3.
Remove exhaust front tube. Refer to
EX-12, "Removal and Installation"
Bolt symbol
Quantity
4
2
Bolt length
“L” mm (in)
40 (1.57)
40 (1.57)
Insertion direction
Transfer to transaxle
Transaxle to transfer
JSDIA5355ZZ
Transfer assembly
: N·m (kg-m, ft-lb)
*: Apply anti-corrosion oil.
JSDIA6394GB
DLN-82
< UNIT REMOVAL AND INSTALLATION >
[TRANSFER: TY21C]
TRANSFER ASSEMBLY
4.
Remove propeller shaft. Refer to
DLN-214, "Removal and Installation"
.
5.
Remove transfer assembly mounting bolts.
6.
Remove transfer assembly from the vehicle.
INSTALLATION
Note the following, and install in the reverse order of removal.
• When installing the transfer to the transaxle, install the mounting
bolts following the standard below, tighten bolts to the specified
torque. For each tightening torque, refer to
.
CAUTION:
• Apply anti-corrosion oil to the thread and seat of mounting bolts.
• Never damage O-ring of transfer.
• Perform inspection after installation. Refer to
.
QR25DE : Inspection
INFOID:0000000011002861
INSPECTION AFTER INSTALLATION
When oil leaks while removing/installing transfer assembly, check oil level after the installation. Refer to
.
Bolt symbol
Quantity
4
2
Bolt length
“L” mm (in)
40 (1.57)
40 (1.57)
Insertion direction
Transfer to transaxle
Transaxle to transfer
JSDIA5355ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст