Nissan X-Trail 32. Instruction — part 1804
SE-64
< REMOVAL AND INSTALLATION >
SECOND SEAT (SLIDING TYPE)
3.
Disengage seat cushion trim fixing retainers
, and then remove seat cushion trim and seat cushion pad
as a set.
4.
Remove seat cushion silencer.
5.
Remove hog rings, and then separate seat cushion trim and seat cushion pad.
CAUTION:
Before performing separating operation, check the installation position of hog rings.
6.
Remove the following parts after removing seat cushion trim and pad.
Seat Rail
1.
Disengage towel bar fixing portion
using a remover tool
(A), and then pull out towel bar.
2.
Remove seat cushion inside finisher outer side. Refer to
SE-65, "SEAT CUSHION FINISHER : Disas-
.
3.
Remove seat rail fixing nuts
, and then remove seat rail.
Seat Control Cable 2 (if equipped)
1.
Remove seat cushion inside finisher outer side. Refer to
SE-65, "SEAT CUSHION FINISHER : Disas-
.
Second seat RH
Second seat LH
JMJIA9681ZZ
JMJIA9682ZZ
JMJIA9683ZZ
SECOND SEAT (SLIDING TYPE)
SE-65
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
2.
Remove seat control cable 2 fixing screw
, then disengage seat control cable 2 fixing clips accord-
ing to the numerical order 1
→
2 as shown in the figure, and then remove seat control cable 2.
ASSEMBLY
Note the following items, and then assemble in the reverse order of disassembly.
CAUTION:
• For hog ring that is removed or crimped unsuccessfully, fix it by using a new hog ring. (Never reuse
hog ring.)
• Always install the hog rings in position.
SEAT CUSHION FINISHER
SEAT CUSHION FINISHER : Disassembly and Assembly
INFOID:0000000010713149
DISASSEMBLY
Seat Cushion Outside Finisher Outer Side
1.
Remove screw cap.
a.
Apply protective tape (A) on the parts to protect it from damage.
b.
Disengage screw cap fixing pawls using a remover tool (A), and
then remove screw cap.
: Clip
JMJIA9684ZZ
JMJIA9685ZZ
: Pawl
JMJIA9686ZZ
SE-66
< REMOVAL AND INSTALLATION >
SECOND SEAT (SLIDING TYPE)
2.
Remove seat cushion outside finisher outer side fixing screw
,
then disengage seat cushion outside finisher outer side fixing
clip, pawls, and then remove seat cushion outside finisher outer
side.
Seat Cushion Outside Finisher Inner Side
Second Seat RH
• Disengage seat cushion outside finisher inner side fixing clips,
pawls, and then remove seat cushion outside finisher inner side.
Second Seat LH
1.
Disengage seat cushion outside finisher inner side fixing clips,
pawls, and then remove seat cushion outside finisher inner side.
2.
Remove seat cushion outside finisher inner side.
Seat Cushion Inside Finisher Outer Side
1.
Remove seatback frame. Refer to
SE-58, "SEATBACK : Disassembly and Assembly"
.
2.
Remove seat cushion trim and seat cushion pad as a set. Refer to
SE-63, "SEAT CUSHION : Disassem-
: Clip
: Pawl
JMJIA9687ZZ
: Clip
: Pawl
JMJIA9688ZZ
: Clip
: Pawl
JMJIA9689ZZ
JMJIA9690ZZ
SECOND SEAT (SLIDING TYPE)
SE-67
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
3.
Remove seat cushion inside finisher outer side fixing clip
, and
then remove seat cushion inside finisher outer side.
Seat Cushion Inside Finisher Inner Side
Second Seat RH
1.
Remove seat cushion trim and seat cushion pad as a set. Refer to
SE-63, "SEAT CUSHION : Disassem-
2.
Remove seat cushion outside finisher inner side.
3.
Remove seat cushion inside finisher inner side rear.
-
Disengage seat cushion inside finisher inner side rear fixing
pawl.
-
Disengage seat cushion inside finisher inner side rear fixing clip,
and then remove seat cushion inside finisher inner side rear.
4.
Disengage seat cushion inside finisher inner side front fixing
clip, and then remove seat cushion inside finisher inner side
front.
Second seat LH
1.
Remove seat cushion trim and seat cushion pad as a set. Refer to
SE-63, "SEAT CUSHION : Disassem-
JMJIA9691ZZ
: Pawl
JMJIA9692ZZ
: Clip
JMJIA9693ZZ
: Clip
JMJIA9694ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст