Nissan X-Trail 32. Instruction — part 1773
RSU-14
< REMOVAL AND INSTALLATION >
REAR SUSPENSION ARM
• RHD: Refer to
.
9.
Remove rear wheel hub assembly and back plate.
• 2WD: Refer to
.
• 4WD: Refer to
.
10. Removal rear hight sensor (with LED head lamp). Refer to
EXL-200, "REAR HEIGHT SENSOR :
.
11. Set jack suspension arm.
CAUTION:
• Check the stable condition when using a jack.
• Never damage rear lower link with a jack.
12. Remove coil spring from suspension arm. Refer to
RSU-9, "Removal and Installation"
.
13. Remove suspension arm bracket and suspension arm from vehicle.
CAUTION:
Remove suspension arm bracket and suspension arm as a set.
14. Remove suspension arm bracket from suspension arm.
15. Perform inspection after removal. Refer to
INSTALLATION
Note the following, and install in the reverse order of removal.
• Align the matching marks that have been made during removal when reusing the disc rotor.
• After installin, perform the air bleeding. Refer to
BR-14, "Bleeding Brake System"
• Perform final tightening of fixing parts at the vehicle installation position (rubber bushing), under unladen
conditions with tires on level ground.
• Be careful about the direction of arm stopper. (Vehicle side: Circule, Inside: Octagon)
• Perform inspection after installation. Refer to
Inspection
INFOID:0000000010822787
INSPECTION AFTER REMOVAL
Check suspension arm and bushing for deformation, crack, and damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connector. Refer to
.
2.
Check wheel alignment. Refer to
3.
Adjust neutral position of steering angle sensor. Refer to
.
4.
After final tightening, install rear hight sensor (with LED head lamp). Refer to
LOWER LINK
RSU-15
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
LOWER LINK
Exploded View
INFOID:0000000010822788
Removal and Installation
INFOID:0000000010822789
REMOVAL
1.
Remove tires. Refer to
WT-61, "Removal and Installation"
.
2.
Removal rear hight sensor (with LED head lamp). Refer to
EXL-200, "REAR HEIGHT SENSOR :
.
3.
Separate stablize link from lower link. Refer to
RSU-19, "Removal and Installation"
4.
Set jack suspension arm.
CAUTION:
• Check the stable condition when using a jack.
• Never damage rear lower link with a jack.
5.
Remove lower link from suspension arm.
6.
Remove lower link from suspension member.
7.
Perform inspection after removal. Refer to
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of fixing parts at the vehicle installation position (rubber bushing), under unladen
conditions with tires on level ground.
• Perform inspection after installation. Refer to
Inspection
INFOID:0000000010822790
INSPECTION AFTER REMOVAL
Check suspension arm and bushing for deformation, crack, and damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel alignment. Refer to
Lower link
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: Vehicle front
JSEIA0907GB
RSU-16
< REMOVAL AND INSTALLATION >
LOWER LINK
2.
Adjust neutral position of steering angle sensor. Refer to
.
3.
After final tightening, install rear hight sensor (with LED head lamp). Refer to
UPPER LINK
RSU-17
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
UPPER LINK
Exploded View
INFOID:0000000010822791
Removal and Installation
INFOID:0000000010822792
REMOVAL
1.
Remove tires. Refer to
WT-61, "Removal and Installation"
.
2.
Remove wheel sensor and sensor harness. Refer to
BRC-214, "REAR WHEEL SENSOR : Removal and
.
3.
Set jack suspension arm.
CAUTION:
• Check the stable condition when using a jack.
• Never damage rear lower link with a jack.
4.
Remove upper link from suspension arm.
5.
Remove upper link bracket from rear suspension member.
6.
Perform inspection after removal. Refer to
INSTALLATION
Note the following, and install in the reverse order of removal.
• Align the matching marks that have been made during removal when reusing the disc rotor.
• Perform final tightening of fixing parts at the vehicle installation position (rubber bushing), under unladen
conditions with tires on level ground.
• Perform inspection after installation. Refer to
Inspection
INFOID:0000000010822793
INSPECTION AFTER REMOVAL
Check suspension arm and bushing for deformation, crack, and damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
Rear suspension member
Lower link
Suspension arm
Bound bumper
Upper link
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: Vehicle front
JSEIA0908GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст