Nissan X-Trail 32. Instruction — part 1772

RSU-10

< REMOVAL AND INSTALLATION >

COIL SPRING

• Securely install coil spring with the lower end aligned with the

steps of lower rubber seat.

CAUTION:

The lower rubber seat protrusion must be securely inserted
into the hole of rear suspension arm.

• Install coil spring

by aligning lower end of coil spring with lower

rubber seat

as shown in the figure.

CAUTION:

Set coil spring so that its paint mark

is aligned with the

position of 1.75 turns from the bottom end of the coil spring.

• Perform final tightening of fixing parts at the vehicle installation position (rubber bushing), under unladen

conditions with tires on level ground.

• Perform inspection after installation. Refer to

RSU-10, "Inspection"

.

Inspection

INFOID:0000000010822780

INSPECTION AFTER REMOVAL

Check rear lower link, rubber seat, upper seat, and coil spring for deformation, crack, and damage. Replace it
if necessary.

INSPECTION AFTER INSTALLATION

1.

Check wheel sensor harness for proper connector. Refer to

BRC-213, "REAR WHEEL SENSOR :

Exploded View"

.

2.

Check wheel alignment. Refer to

RSU-7, "Inspection"

.

3.

Adjust neutral position of steering angle sensor. Refer to

BRC-99, "Work Procedure"

.

SEIA0636J

Dimension (A)

: 5 mm (0.20 in) or less

JSEIA0671ZZ

ALEIA0210ZZ

REAR SHOCK ABSORBER

RSU-11

< REMOVAL AND INSTALLATION >

C

D

F

G

H

I

J

K

L

M

A

B

RSU

N

O

P

REAR SHOCK ABSORBER

Exploded View

INFOID:0000000010822781

Removal and Installation

INFOID:0000000010822782

REMOVAL

1.

Remove tires. Refer to

WT-61, "Removal and Installation"

.

2.

Set jack (A) under suspension arm to relieve the coil spring tension.

CAUTION:

• Check the stable condition when using a jack.
• Never damage suspesion arm with a jack.

3.

Remove shock absorber mounting bolt (Upper and lower side).

4.

Remove shock absorber.

5.

Perform inspection after removal. Refer to

RSU-11, "Inspection"

.

INSTALLATION

Note the following, and install in the reverse order of removal.
• Perform final tightening of fixing parts at the vehicle installation position (rubber bushing), under unladen

conditions with tires on level ground.

• Perform inspection after installation. Refer to

RSU-11, "Inspection"

.

• After replacing the shock absorber, always follow the disposal procedure to discard the shock absorber.

Refer to

RSU-12, "Disposal"

.

Inspection

INFOID:0000000010822783

INSPECTION AFTER DISASSEMBLY

Check the following items, and replace the part if necessary.
• Shock absorber for deformation, cracks, and other damage.
• Piston rod for damage, uneven wear, and distortion.
• Oil leakage

INSPECTION AFTER INSTALLATION

1.

Check wheel alignment. Refer to

RSU-7, "Inspection"

.

Rear suspension member

shock absorber

Suspension arm

: N·m (kg-m, ft-lb)

: Vehicle front

JSEIA0904GB

RSU-12

< REMOVAL AND INSTALLATION >

REAR SHOCK ABSORBER

2.

Adjust neutral position of steering angle sensor. Refer to

BRC-99, "Work Procedure"

.

Disposal

INFOID:0000000010822784

1.

Set shock absorber horizontally to the ground with the piston rod fully extracted.

2.

Drill 2 – 3 mm (0.08 – 0.12 in) hole at the position (

) from top

as shown in the figure to release gas gradually.

CAUTION:

• Wear eye protection (safety glasses).
• Wear gloves.
• Be careful with metal chips or oil blown out by the com-

pressed gas.

NOTE:
• Drill vertically in this direction show by arrow.
• Directly to the outer tube avoiding brackets.
• The gas is clear, colorless, odorless, and harmless.

3.

Position the drilled hole downward and drain oil by moving the piston rod several times.

CAUTION:

Dispose of drained oil according to the law and local regulations.

A

: 20 – 30 mm (0.79 – 1.18 in)

JPEIA0161ZZ

REAR SUSPENSION ARM

RSU-13

< REMOVAL AND INSTALLATION >

C

D

F

G

H

I

J

K

L

M

A

B

RSU

N

O

P

REAR SUSPENSION ARM

Exploded View

INFOID:0000000010822785

Removal and Installation

INFOID:0000000010822786

REMOVAL

1.

Remove tires. Refer to

WT-61, "Removal and Installation"

.

2.

Drain brake fluid.
• LHD: Refer to

BR-13, "Draining"

.

• RHD: Refer to

BR-77, "Draining"

.

3.

Remove wheel sensor and sensor harness. Refer to

BRC-214, "REAR WHEEL SENSOR : Removal and

Installation"

.

4.

Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work.
• LHD: Refer to

BR-63, "BRAKE CALIPER ASSEMBLY : Removal and Installation"

.

• RHD: Refer to

BR-123, "BRAKE CALIPER ASSEMBLY : Removal and Installation"

.

CAUTION:

Never depress brake pedal while brake caliper is removed.

5.

Remove disc rotor.
• 2WD: Refer to

RAX-7, "Removal and Installation"

.

• 4WD: Refer to

RAX-18, "Removal and Installation"

.

CAUTION:

• Put matching marks on the wheel hub assembly and the disc rotor before removing the disc

rotor.

• Never drop disc rotor.

6.

Remove parking brake cable mounting bolt. Refer to

PB-154, "Exploded View"

.

7.

Separate the brake tube from the brake hose, and then remove rock plate.
• LHD: Refer to

BR-29, "REAR : Removal and Installation"

.

• RHD: Refer to

BR-92, "REAR : Removal and Installation"

.

8.

Remove brake tube from suspension arm.
• LHD: Refer to

BR-27, "REAR : Exploded View"

.

Suspension arm bracket

Suspension bar

Arm stopper

Suspension arm

: Always replace after every disassembly.

: N·m (kg-m, ft-lb)

: Vehicle front

JSEIA0906GB