Nissan X-Trail 32. Instruction — part 41
AV-156
< BASIC INSPECTION >
[WITH NAVIGATION]
DIAGNOSIS AND REPAIR WORKFLOW
-
Record DTC and Freeze Frame Data.
Is DTC displayed?
YES
>> GO TO 3.
NO
>> GO TO 4.
3.
TROUBLE DIAGNOSIS FOR DTC
1.
Check the DTC indicated in the self-diagnosis results.
2.
Perform the relevant diagnosis referring to the DTC Index. Refer to
>> GO TO 5.
4.
TROUBLE DIAGNOSIS FOR SYMPTOMS
Perform the relevant diagnosis referring to the diagnosis chart by symptom. Refer to
.
>> GO TO 5.
5.
ERROR PART REPAIR
1.
Repair or replace the identified malfunctioning parts.
2.
Perform a self-diagnosis for “AVM” with CONSULT.
NOTE:
Erase the stored self-diagnosis results after repairing or replacing the relevant components if any DTC
has been indicated in the self-diagnosis results.
3.
Check that the symptom does not occur.
Does the symptom occur?
YES
>> GO TO 1.
NO
>> INSPECTION END
AV
INSPECTION AND ADJUSTMENT
AV-157
< BASIC INSPECTION >
[WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING NAVI CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING NAVI CONTROL UNIT : Description
INFOID:0000000010714819
Perform the following operations when replacing NAVI control unit.
Configuration, refer to
AV-157, "CONFIGURATION (NAVI CONTROL UNIT) : Work Procedure"
CONFIGURATION (NAVI CONTROL UNIT)
CONFIGURATION (NAVI CONTROL UNIT) : Description
INFOID:0000000010714820
• Since vehicle specifications are not included in the NAVI control unit after replacement, it is required to write
vehicle specifications with CONSULT.
• The NAVI control unit configuration includes functions as follows.
CONFIGURATION (NAVI CONTROL UNIT) : Work Procedure
INFOID:0000000010714821
1.
SAVING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “Before Replace ECU”, and save the current vehicle specification in CONSULT.
Is the vehicle specification saved normally?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
REPLACE NAVI CONTROL UNIT
Replace NAVI control unit. Refer to
AV-262, "Removal and Installation"
>> GO TO 3.
3.
WRITING VEHICLE SPECIFICATION
CONSULT Configuration
Select “Configuration” or “After Replace ECU”, and write the vehicle specification saved in CONSULT to NAVI
control unit.
>> GO TO 6.
4.
REPLACE NAVI CONTROL UNIT
Replace NAVI control unit. Refer to
AV-262, "Removal and Installation"
>> GO TO 5.
5.
WRITE VEHICLE SPECIFICATION
CONSULT Configuration
Select “Instruction Configuration”, and write the setting value as shown in the following table to NAVI control unit
according to the vehicle specification.
CAUTION:
Grasp vehicle specifications precisely. The control of ECU may not function normally if the specifica-
tions are misread.
Function
Description
Read/Write Configuration
Before Replace ECU
Allows the reading of vehicle specification written in NAVI control
unit to store the specification in CONSULT.
After Replace ECU
Allows the writing of the vehicle information stored in CONSULT
into the NAVI control unit.
Instruction Configuration
Allows the writing of the vehicle specification into the NAVI control
unit by hand.
AV-158
< BASIC INSPECTION >
[WITH NAVIGATION]
INSPECTION AND ADJUSTMENT
NOTE:
• The items shown in this list depend on vehicle specifications.
• The config list may not be displayed depending on vehicle specifications. This is not a malfunction.
• If selection items are not displayed on the CONSULT screen, touch “NEXT”.
>> GO TO 6.
6.
PERFORM SELF-DIAGNOSIS
CONSULT Self Diagnostic Result
Perform self-diagnosis of CONSULT, and check whether or not DTC U12AA is detected.
Is DTC U12AA detected?
>> GO TO 5.
>> GO TO 7.
7.
OPERATION CHECK
Check that the operation of the NAVI control unit is normal.
>> WORK END
ADDITIONAL SERVICE WHEN REPLACING AROUND VIEW MONITOR CON-
TROL UNIT
ADDITIONAL SERVICE WHEN REPLACING AROUND VIEW MONITOR CONTROL
UNIT : Description
INFOID:0000000010714822
• Always perform the around view monitor control unit configuration after replacing the around view monitor
control unit.
• Always perform the around view monitor calibration after removing and installing or replacing the rear cam-
era.
• Always perform the rear camera calibration after removing and installing or replacing the rear camera.
• Always perform the rear camera calibration after replacing the around view monitor control unit.
• Always perform the around view monitor calibration after replacing the around view monitor control unit.
CAUTION:
MANUAL SETTING ITEM
Detail
Items
Setting value
STEERING
LHD
LHD models
RHD
RHD models
ENGINE TYPE
GASOLINE
Gasoline engine models
DIESEL
Diesel engine models
TRANSMISSION
MT
M/T models
CVT
CVT models
CAMERA SYSTEM
NONE/AVM
• Without around view monitor system
• With around view monitor system without park assist
REAR CAMERA
With rear view monitor system
AVM+PA
With around view monitor system and park assist
SOUND SYSTEM
BASE
Without BOSE system
BOSE
With BOSE system
ENGINE TYPE
NORMAL
Gasoline or diesel engine
HYBRID
Hybrid
FRONT CAMERA
WITHOUT
Without front camera
WITH
With front camera
AV
INSPECTION AND ADJUSTMENT
AV-159
< BASIC INSPECTION >
[WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
The system does not operate normally unless the around view monitor and rear camera calibration are
performed. Always perform it.
ADDITIONAL SERVICE WHEN REPLACING AROUND VIEW MONITOR CONTROL
UNIT : Work Procedure
INFOID:0000000010714823
1.
AROUND VIEW MONITOR CONTROL UNIT CONFIGURATION
Perform the around view monitor control unit configuration with CONSULT. Refer to
TION (AROUND VIEW MONITOR CONTROL UNIT) : Work Procedure"
.
>> GO TO 2.
2.
AROUND VIEW MONITOR CONTROL UNIT CALIBRATION
Perform the around view monitor calibration with CONSULT. Refer to
IMAGE (AROUND VIEW MONITOR) : Work Procedure"
.
>> GO TO 3.
3.
REAR CAMERA CALIBRATION
Perform the rear camera calibration with CONSULT. Refer to
DAS-110, "Work Procedure (Preparation)"
.
>> GO TO 4.
4.
PERFORM SELF-DIAGNOSIS
Perform the self-diagnosis of around view monitor control unit with CONSULT (AVM). Check if any DTC is
detected.
Is any DTC detected?
YES
>> Perform the trouble diagnosis for the detected DTC. Refer to
NO
>> GO TO 5.
5.
LDW AND BSW SYSTEM ACTION TEST
1.
Perform the BSW and DAA system action test. Refer to
DAS-92, "BSW : Work Procedure"
(BSW) and
DAS-95, "DAA : Work Procedure"
(DAA).
2.
Check that the BSW and DAA system operates normally.
>> WORK END
CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT)
CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT) : Work Procedure
INFOID:0000000010714824
1.
SAVING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “Before Replace ECU”, and save the current vehicle specification in CONSULT.
Is the vehicle specification saved normally?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
REPLACE AROUND VIEW MONITOR CONTROL UNIT
Replace around view monitor control unit. Refer to
AV-268, "Removal and Installation"
>> GO TO 3.
3.
WRITING VEHICLE SPECIFICATION
CONSULT Configuration
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст