Nissan X-Trail 32. Instruction — part 1469
REAR DOOR FINISHER
INT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
c.
Apply protective tapes (A) on rear door finisher to protect it from
damage.
d.
Disengage power window switch finisher fixing pawls using a
remover tool (A).
e.
Disconnect power window switch harness connector, and then remove power window switch finisher and
power window switch as a set.
NOTE:
Remove power window switch after removing power window switch finisher. Refer to
3.
Remove rear door finisher fixing screw
.
4.
Apply protective tape (A) on rear door panel to protect it from
damage.
JMJIB0160ZZ
: Pawl
JMJIB0161ZZ
JMJIB0162ZZ
JMJIB0163ZZ
INT-22
< REMOVAL AND INSTALLATION >
REAR DOOR FINISHER
5.
Disengage rear door finisher fixing clips using a remover tool
(A), and then remove rear door finisher according to numerical
order 1
→
2 indicated by arrows as shown in the figure.
CAUTION:
Insert a remover tool between rear door panel and fixing
clip.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Visually check clips for deformation and damage during installation. Replace with new ones if neces-
sary.
• Check in advance that clips and pawls are accurately aligned with the portions on rear door panel,
and then install by pressing in.
: Clip
JMJIB0164ZZ
BODY SIDE TRIM
INT-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
BODY SIDE TRIM
Exploded View
INFOID:0000000010730549
FRONT PILLAR GARNISH
FRONT PILLAR GARNISH : Removal and Installation
INFOID:0000000010730550
CAUTION:
Never damage the body panel.
REMOVAL
1.
Release front pillar garnish portion of front body side welt.
Front pillar garnish
Front body side welt
Dash side finisher
Dash clip
Front kicking plate
Harness clip
Center pillar lower garnish
Seat belt cover
Metal clip
Rear kicking plate
Rear body side welt
Center pillar upper garnish
: Clip
: Pawl
: Always replace after every disassembly.
JMJIB0100ZZ
INT-24
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
2.
Disengage front pillar garnish fixing anchor clips according to
numerical order 1
→
2 indicated by arrows as shown in the figure.
3.
Cut anchor clip portion.
4.
Remove front pillar garnish.
5.
Remove front pillar garnish anchor clips from the body panel.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Always replace anchor clips with a new one after every removal.
• Be sure to install anchor clip to front pillar garnish before installing front pillar garnish.
• Check fixing portions of front pillar garnish bottom end portion are engaged to instrument panel,
and then engage anchor clips in order from upper side.
• Check in advance that anchor clips are accurately aligned with the portions on body panel, and then
install by pressing in.
KICKING PLATE
KICKING PLATE : Removal and Installation
INFOID:0000000010730551
CAUTION:
Never damage the body panel.
REMOVAL
Front Kicking Plate
: Anchor clip
JMJIA9603ZZ
JMJIA5130ZZ
JMJIA9604ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст