Nissan X-Trail 32. Instruction — part 1470
BODY SIDE TRIM
INT-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
1.
Disengage front kicking plate fixing pawls of front end portion according to numerical order 1
→
2 indicated
by arrows as shown in the figure.
2.
Disengage front kicking plate fixing pawls of center portion
according to numerical order 1
→
3 indicated by arrows as shown
in the figure.
3.
Disengage front kicking plate fixing pawls of rear end portion according to numerical order 1
→
2 indicated
by arrows as shown in the figure, and then remove front kicking plate.
Rear Kicking Plate
1.
Disengage rear kicking plate fixing pawls of front end portion according to numerical order 1
→
2 indicated
by arrows as shown in the figure.
: Pawl
: Vehicle front
JMJIA9605ZZ
: Pawl
: Vehicle front
JMJIA9607ZZ
: Pawl
: Vehicle front
JMJIA9606ZZ
JMJIA9608ZZ
INT-26
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
2.
Disengage rear kicking plate fixing clips and fixing pawls of rear end portion according to numerical order
1
→
3 indicated by arrows as shown in the figure, and then remove rear kicking plate.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Visually check clips for deformation and damage during installation. Replace with new ones if neces-
sary.
• Check in advance that clips and pawls are accurately aligned with the portions on body panel, and
then install by pressing in.
DASH SIDE FINISHER
DASH SIDE FINISHER : Removal and Installation
INFOID:0000000010730552
CAUTION:
Never damage the body panel.
REMOVAL
1.
Remove front kicking plate. Refer to
INT-24, "KICKING PLATE : Removal and Installation"
.
2.
Remove instrument lower cover (passenger side). Refer to the following.
• LHD models: Refer to
IP-14, "Removal and Installation"
.
• RHD models: Refer to
IP-41, "Removal and Installation"
3.
Remove dash clip
and disengage dash side finisher fixing
clip, and then remove dash side finisher.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Visually check clip for deformation and damage during installation. Replace with new ones if neces-
sary.
: Pawl
: Vehicle front
: Clip
: Pawl
: Vehicle front
JMJIA9609ZZ
: Clip
JMJIA9611ZZ
BODY SIDE TRIM
INT-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
• Check in advance that clip are accurately aligned with the portion on body panel, and then install by
pressing in.
BODY SIDE WELT
BODY SIDE WELT : Removal and Installation
INFOID:0000000010730553
CAUTION:
• Never excessively pull body side welt.
• Never damage the body panel.
REMOVAL
Front Body Side Welt
1.
Remove front kicking plate. Refer to
INT-24, "KICKING PLATE : Removal and Installation"
.
2.
Remove front body side welt.
Rear Body Side Welt
1.
Remove rear kicking plate. Refer to
INT-24, "KICKING PLATE : Removal and Installation"
2.
Remove rear body side welt.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
NOTE:
Align body side welt identification mark and vehicle position mark, and then install body side welt.
CENTER PILLAR LOWER GARNISH
CENTER PILLAR LOWER GARNISH : Removal and Installation
INFOID:0000000010730554
CAUTION:
Never damage the body panel.
REMOVAL
1.
Fully open front door and rear door.
2.
Move front seat to the frontmost position.
3.
Remove front kicking plate and rear kicking plate. Refer to
INT-24, "KICKING PLATE : Removal and
.
4.
Release center pillar lower garnish portion of front body side welt and rear body side welt.
5.
Pull up seat belt cover and disengage seat belt cover fixing
pawls, and then remove seat belt cover.
: Pawl
JMJIA9612ZZ
INT-28
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
6.
Disengage center pillar lower garnish fixing pawls and clips according to numerical order 1
→
4 indicated
by arrows as shown in the figure, and then remove center pillar lower garnish.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Visually check clips for deformation and damage during installation. Replace with new ones if neces-
sary.
• Check in advance that clips and pawls are accurately aligned with the portions on center pillar upper
garnish and body panel, and then install by pressing in.
CENTER PILLAR UPPER GARNISH
CENTER PILLAR UPPER GARNISH : Removal and Installation
INFOID:0000000010730555
CAUTION:
Never damage the body panel.
REMOVAL
1.
Remove center pillar lower garnish. Refer to
INT-27, "CENTER PILLAR LOWER GARNISH : Removal
2.
Remove seat belt shoulder anchor. Refer to
SB-10, "SEAT BELT RETRACTOR : Removal and Installa-
3.
Release center pillar upper garnish portion of front body side welt and rear body side welt.
4.
Disengage center pillar upper garnish lower side fixing pawl.
5.
Disengage center pillar upper garnish upper side fixing pawl according to numerical order 1
→
4 indicated
by arrows as shown in the figure, and then remove center pillar upper garnish.
NOTE:
Removal operation can be performed easily when pressing pawl by inserting a remover tool from direction
as shown in the figure.
: Clip
: Pawl
JMJIA9760ZZ
: Pawl
JMJIA9614ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст