Nissan X-Trail 32. Instruction — part 570
BACK DOOR LOCK
DLK-621
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Disconnect spindle unit harness connector.
4.
Remove harness grommet
from back main center pillar
,
and then pull out spindle unit harness from vehicle body.
5.
Support back door with the proper material to prevent it from falling.
WARNING:
Bodily injury may occur if no supporting rod is holding the back door open when removing the
back door stay.
6.
Apply protective tape (A) to back door touch sensor around spin-
dle unit for preventing damage.
7.
Remove metal clip
located on connection between back door
stay
and stud ball
using a remover tool (A) according to the
numerical order 1
→
2 indicated by arrows as shown in the figure.
8.
Disengage spindle unit and stud ball of back door side.
9.
Remove back door stay upper bracket mounting bolts, and then remove spindle unit with back door stay
upper bracket.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
: Vehicle front
JMKIB3153ZZ
JMKIB3154ZZ
JMKIB3155ZZ
JMKIA2255ZZ
DLK-622
< REMOVAL AND INSTALLATION >
[TYPE 2]
BACK DOOR LOCK
• Perform calibration of automatic back door position information. Refer to
.
• After installation, check back door lock. Refer to
DLK-619, "DOOR LOCK : Inspection"
TOUCH SENSOR
TOUCH SENSOR : Removal and Installation
INFOID:0000000010728168
REMOVAL
1.
Remove back door inner finisher. Refer to
INT-47, "Removal and Installation"
2.
Disconnect back door touch sensor harness connector
.
3.
Remove spindle unit of back door side.
4.
Remove back door touch sensor fixing clips, and then remove back door touch sensor while tearing off
double-sided tape.
5.
Remove harness grommet
from back door panel
, and then
pull out back door touch sensor harness from back door panel
and remove back door touch sensor
.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Before installing, remove double-sided tape remaining on back door touch sensor and back door
panel neatly.
• When installing, apply primer for resin to double-sided tape sticking point of back door touch sensor
and back door panel.
• After installing, check that there is no clearance between back door touch sensor and back door
panel.
• After installing, check that back door turns over normally by back door touch sensor.
• After installation, check door lock. Refer to
DLK-619, "DOOR LOCK : Inspection"
.
: Vehicle front
JMKIB3156ZZ
: Vehicle front
JMKIB3157ZZ
FUEL FILLER LID OPENER
DLK-623
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FUEL FILLER LID OPENER
Exploded View
INFOID:0000000010728169
Fuel filler lid opener cable
Cable protector
Fuel filler lid lock assembly
Bumper rubber
Fuel filler lid assembly
Spring
: Clip
: Pawl
: Always replace after every disassembly.
JMKIB3488ZZ
DLK-624
< REMOVAL AND INSTALLATION >
[TYPE 2]
FUEL FILLER LID OPENER
FUEL FILLER LID
FUEL FILLER LID : Removal and Installation
INFOID:0000000010728170
REMOVAL
1.
Fully open fuel filler lid.
2.
Remove fuel mounting pin
.
3.
Remove mounting bolts, and then remove fuel filler lid assembly.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• After installation, apply the touch-up paint (the body color) onto the head of the mounting screws.
• After installation, check fuel filler lid assembly open/close, lock/unlock operation.
NOTE:
• The following table shows the specified values for checking normal installation status.
• Fitting adjustment cannot be performed.
Unit: mm [in]
FUEL FILLER LID LOCK
FUEL FILLER LID LOCK : Removal and Installation
INFOID:0000000010728171
REMOVAL
1.
Fully open fuel filler lid.
2.
Remove luggage side lower finisher RH. Refer to
INT-43, "LUGGAGE SIDE LOWER FINISHER :
.
3.
Rotate fuel filler lid lock assembly to disengage pawls and
remove fuel filler lid lock assembly according to the numerical
order 1
→
2 indicated by arrows as shown in the figure.
NOTE:
Operation is performed easily when rotating fuel filler lid lock
from passenger room side.
JMKIB3183ZZ
Clearance
Evenness
Fuel filler lid – Body side outer
2.5 – 4.5
[0.098 – 0.177]
(
−
1.0) – (+1.0)
[(
−
0.039) – (+0.039)]
: Pawl
: Vehicle front
JMKIB1094ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст