Nissan X-Trail 32. Instruction — part 569
REAR DOOR LOCK
DLK-617
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000010728162
REMOVAL
1.
Fully close the rear door glass.
2.
Remove rear door finisher. Refer to
INT-19, "Removal and Installation"
.
3.
Remove inside handle. Refer to
DLK-616, "INSIDE HANDLE : Removal and Installation"
.
4.
Remove sealing screen and rear door lower sash. Refer to
GW-52, "REAR DOOR LOWER SASH :
.
5.
Remove door side grommet
, and then loosen TORX bolt
from grommet hole.
6.
Remove outside handle escutcheon
while pulling outside
handle grip
according to the numerical order 1
→
2 indicated
by arrows as shown in the figure.
7.
Slide outside handle grip
toward rear of vehicle and remove it
according to the numerical order 1
→
2 indicated by arrows as
shown in the figure.
JMKIB3528ZZ
JMKIB2479ZZ
JMKIA0524ZZ
DLK-618
< REMOVAL AND INSTALLATION >
[TYPE 2]
REAR DOOR LOCK
8.
Remove front gasket
and rear gasket
.
9.
Slide outside handle bracket toward rear of vehicle and remove
it.
10. Disconnect outside handle cable
from outside handle bracket
according to the numerical order 1
→
2 indicated by arrows as
shown in the figure.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• When installing outside handle cable to outside handle, be careful that outside handle cable is
routed normally.
• After installation, check door lock. Refer to
DLK-616, "DOOR LOCK : Inspection"
.
: Pawl
: Vehicle front
JMKIB1627ZZ
: Vehicle front
JMKIB2034ZZ
JMKIB3525ZZ
BACK DOOR LOCK
DLK-619
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR LOCK
Exploded View
INFOID:0000000010728163
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000010728164
REMOVAL
1.
Remove back door inner finisher. Refer to
INT-47, "Removal and Installation"
2.
Disconnect back door lock & remote control assembly harness connector.
3.
Remove back door lock & remote control assembly mounting bolts, and then remove back door lock &
remote control assembly from back door panel.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
After installation, check back door lock. Refer to
DLK-619, "DOOR LOCK : Inspection"
DOOR LOCK : Inspection
INFOID:0000000010728165
1.
After opening and closing the back door, check that door is fixed to the vehicle body normally.
Back door panel
Spindle unit
Back door stay upper bracket
Double-sided tape
[t: 1.2 mm (0.047 in)]
Back door touch sensor
Back door lock & remote control as-
sembly
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Body grease
,
,
: Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIB3552GB
DLK-620
< REMOVAL AND INSTALLATION >
[TYPE 2]
BACK DOOR LOCK
2.
Check the lock/unlock operation of door lock.
3.
Check door lock assembly for poor lubrication. Apply body
grease to door lock if necessary.
DOOR LOCK : Unlock procedures
INFOID:0000000010728166
UNLOCK PROCEDURES
NOTE:
Release lock according to the following procedures when lock cannot be unlocked due to a malfunction of
door lock assembly or battery discharge.
Insert a screwdriver, etc. into tool insertion hole
of back door inner finisher
, and then back door lock is
unlocked by operating knob
of cancel lever
in the direction of arrow as shown in the figure.
SPINDLE UNIT
SPINDLE UNIT : Removal and Installation
INFOID:0000000010728167
REMOVAL
1.
Disconnect battery negative terminal. Refer to
PG-139, "R9M : Removal and Installation"
2.
Remove luggage side upper finisher. Refer to
INT-45, "LUGGAGE SIDE UPPER FINISHER : Removal
: Body grease
JMKIB1220ZZ
: Vehicle front
JMKIB3161ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст