Nissan X-Trail 32. Instruction — part 2108
TM-390
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
SHIFT POSITION INDICATOR CIRCUIT
SHIFT POSITION INDICATOR CIRCUIT
Component Parts Function Inspection
INFOID:0000000010622576
1.
CHECK SHIFT POSITION INDICATOR
1.
Start the engine.
2.
Shift selector lever.
3.
Check that the selector lever position and the shift position indicator on the combination meter are identi-
cal.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Go to
Diagnosis Procedure
INFOID:0000000010622577
1.
CHECK TCM INPUT/OUTPUT SIGNAL
With CONSULT
1.
Start the engine.
2.
Select “Data Monitor” in “TRANSMISSION”.
3.
Select “RANGE”.
4.
Shift selector lever.
5.
Check that selector lever position, “RANGE” on CONSULT screen, and shift position indicator display on
combination meter are identical.
Is the check result normal?
YES
>> INSPECTION END
NO-1 (“RANGE” is changed but is not displayed on shift position indicator.>>Check “Self Diagnostic Result”
in “TRANSMISSION”.
NO-2 (“RANGE” and shift position indicator are different.)>>Check “Self Diagnostic Result” in “TRANSMIS-
SION”.
NO-3 (Specific “RANGE” is not displayed on shift position
indicator.)>>Check “Self Diagnostic Result” in
“METER/M&A”.
SHIFT LOCK SYSTEM
TM-391
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SHIFT LOCK SYSTEM
Component Function Check
INFOID:0000000010622578
1.
CHECK SHIFT LOCK OPERATION (PART 1)
1.
Turn ignition switch ON.
2.
Shift the selector lever to “P” position.
3.
Attempt to shift the selector lever to any other than position with the brake pedal released.
Can the selector lever be shifted to any other position?
YES
>> Go to
NO
>> GO TO 2.
2.
CHECK SHIFT LOCK OPERATION (PART 2)
Attempt to shift the selector lever to any other than position with the brake pedal depressed.
Can the selector lever be shifted to any other position?
YES
>> INSPECTION END
NO
>> Go to
Diagnosis Procedure
INFOID:0000000010622579
1.
CHECK POWER SOURCE (PART 1)
1.
Turn ignition switch OFF.
2.
Disconnect stop lamp switch connector
3.
Turn ignition switch ON.
4.
Check the voltage between the stop lamp switch harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 9.
2.
CHECK STOP LAMP SWITCH MOUNTING POSITION
Check stop lamp switch mounting position. Refer to
BR-11, "Inspection and Adjustment"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Adjust stop lamp switch mounting position.
3.
CHECK STOP LAMP SWITCH
Check stop lamp switch. Refer to
TM-394, "Component Inspection (Stop Lamp Switch)"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace stop lamp switch.
4.
CHECK CIRCUIT BETWEEN STOP LAMP SWITCH AND CVT SHIFT SELECTOR
1.
Disconnect CVT shift selector connector
2.
Check the continuity between the stop lamp switch harness connector terminal and the CVT shift selector
harness connector terminal.
+
–
Voltage
Stop lamp switch
Connector
Terminal
E115
3
Ground
Battery voltage
Stop lamp switch
CVT shift selector
Continuity
Connector
Terminal
Connector
Terminal
E115
4
M52
3
Existed
TM-392
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
SHIFT LOCK SYSTEM
3.
Also check short circuit in harness.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace damaged parts.
5.
CHCK GROUND CIRCUIT
Check the continuity between the CVT shift selector harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace damaged parts.
6.
CHECK PART POSITION SWITCH
1.
Disconnect park position switch connector.
2.
Check park position switch. Refer to
TM-393, "Component Inspection (Park Position Switch)"
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace damaged parts.
7.
CHECK SHIFT LOCK SOLENOID
1.
Disconnect shift lock solenoid connector.
2.
Check shift lock solenoid. Refer to
TM-392, "Component Inspection (Shift Lock Solenoid)"
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Repair or replace damaged parts.
8.
CHECK CVT SHIFT SELECTOR HARNESS
Check CVT shift selector harness. Refer to
TM-393, "Component Inspection (CVT Shift Selector Harness)"
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NO
>> Repair or replace damaged parts.
9.
DETECT MALFUNCTIONING ITEM
Check the following items:
• Open or short circuit of the harness between ignition switch and stop lamp switch connector. Refer to
"Wiring Diagram - IGNITION POWER SUPPLY -"
.
• Ignition switch
• 10A fuse [No.30, fuse block (J/B)]. Refer to
PG-84, "Fuse, Connector and Terminal Arrangement"
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NO
>> Repair or replace damaged parts.
Component Inspection (Shift Lock Solenoid)
INFOID:0000000010622580
1.
CHECK SHIFT LOCK SOLENOID
Apply voltage to terminals of shift lock solenoid connector and check that shift lock solenoid is activated.
CAUTION:
• Connect the fuse between the terminals when applying the voltage.
• Never cause shorting between terminals.
CVT shift selector
—
Continuity
Connector
Terminal
M52
4
Ground
Existed
SHIFT LOCK SYSTEM
TM-393
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace shift lock unit. Refer to
TM-404, "Disassembly and Assembly"
Component Inspection (Park Position Switch)
INFOID:0000000010622581
1.
CHECK PARK POSITION SWITCH
Check the continuity between park position switch connector terminals.
CAUTION:
• Connect the fuse between the terminals when applying the voltage.
• Never cause shorting between terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace park position switch. Refer to
TM-404, "Disassembly and Assembly"
Component Inspection (CVT Shift Selector Harness)
INFOID:0000000010622582
1.
CHECK CVT SHIFT SELECTOR HARNESS (PART 1)
Check the continuity between the CVT shift selector harness connector terminal and the shift lock solenoid
harness connector terminal.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace CVT shift selector assembly. Refer to
TM-403, "Removal and Installation"
2.
CHECK CVT SHIFT SELECTOR HARNESS (PART 2)
Check the continuity between the shift lock solenoid harness connector terminal and the park position switch
harness connector terminal.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace CVT shift selector assembly. Refer to
TM-403, "Removal and Installation"
3.
CHECK CVT SHIFT SELECTOR HARNESS (PART 3)
Check the continuity between the park position switch harness connector terminal and the CVT shift selector
harness connector terminal.
+ (fuse)
−
Condition
Status
Shift lock solenoid
Terminal
1
2
Apply battery voltage be-
tween terminals 1 and 2.
Shift lock solenoid operates
Park position switch
Condition
Continuity
Terminal
1 – 2
Shift the selector lever to “P” position.
Existed
Other than above
Not existed
CVT shift selector
Shift lock solenoid
Continuity
Connector
Terminal
Connector
Terminal
M324
3
M326
1
Existed
Shift lock solenoid
Park position switch
Continuity
Connector
Terminal
Connector
Terminal
M326
2
M325
1
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст