Nissan X-Trail 32. Instruction — part 52
AV-200
< DTC/CIRCUIT DIAGNOSIS >
[WITH NAVIGATION]
U111D SIDE CAMERA LH IMAGE SIGNAL CIRCUIT
YES
>> Replace around view monitor control unit. Refer to
AV-268, "Removal and Installation"
NO
>> Replace side camera LH. Refer to
AV-271, "Removal and Installation"
.
AV
U112F EPS CIRCUIT
AV-201
< DTC/CIRCUIT DIAGNOSIS >
[WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
U112F EPS CIRCUIT
DTC Description
INFOID:0000000010923282
DTC DETECTION LOGIC
POSSIBLE CAUSE
EPS
FAIL-SAFE
Around view monitor with Park Assist is cancel
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
WITH CONSULT
1.
Turn the ignition switch ON
2.
Perform “All DTC Reading” with CONSULT.
3.
Check if the “U112F” is detected as the current malfunction in “Self Diagnostic Result” of “AVM”.
“U112F” detected as the current malfunction?
YES
>> Refer to
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010923283
1.
CHECK SELF-DIAGNOSIS RESULTS
With CONSULT.
Check if the “U1000” is detected other than “U112F” in “Self Diagnostic Result” of “AVM”.
“U1000” detected?
YES
>> Perform the CAN communication system inspection. Repair or replace the malfunctioning parts.
AV-178, "AROUND VIEW MONITOR CONTROL UNIT : Diagnosis Procedure"
NO
>> GO TO 2.
2.
CHECK SELF-DIAGNOSIS RESULTS
With CONSULT.
Check if any DTC is detected in “Self Diagnostic Result” of “EPS/DAST3”.
Is any DTC detected?
YES
>> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
.
NO
>> Replace the around view monitor control unit. Refer to
AV-268, "Removal and Installation"
DTC
Trouble diagnosis
(Trouble diagnosis contents)
DTC detecting condition
U112F
EPS CIRC
(EPS circuit)
The around view monitor control unit detects that EPS has a malfunction.
AV-202
< DTC/CIRCUIT DIAGNOSIS >
[WITH NAVIGATION]
U1217 NAVI CONTROL UNIT
U1217 NAVI CONTROL UNIT
DTC Description
INFOID:0000000010714857
DTC DETECTION LOGIC
POSSIBLE CAUSE
NAVI control unit
FAIL-SAFE
The function of some multi-AV systems does not operate
DTC CONFIRMATION PROCEDURE
NOTE:
• The auto ACC function allows the accessory power supply for a certain period of time even after ignition
switch OFF. For this reason, when performing diagnosis, turn the ignition switch OFF and wait for 3 minutes
with the driver's door opened.
• The operation of the vehicle during standby may cause an accessory power supply.
1.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Turn ignition switch ON.
2.
Turn ignition switch OFF and wait for 3 minutes with the driver's door opened.
3.
Turn ignition switch ON and wait at least 30 seconds or more.
4.
Select “Self Diagnostic Result” mode of “MULTI AV” using CONSULT.
5.
Check DTC.
Is DTC U1217 detected?
YES
>> Proceed to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010714858
1.
PERFORM DTC CONFIRMATION PROCEDURE AGAIN
With CONSULT
1.
Turn ignition switch ON.
2.
Erase DTC.
3.
Perform DTC confirmation procedure again. Refer to
.
Is DTC U1217 detected again?
YES
>> Replace NAVI control unit. Refer to
AV-262, "Removal and Installation"
NO
>> INSPECTION END
DTC
Trouble diagnosis
(Trouble diagnosis contents)
Detecting condition
U1217
BLUETOOTH MODULE
(Bluetooth module connection)
NAVI control unit malfunction is detected.
AV
U1229 NAVI CONTROL UNIT
AV-203
< DTC/CIRCUIT DIAGNOSIS >
[WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
U1229 NAVI CONTROL UNIT
DTC Description
INFOID:0000000010714859
DTC DETECTION LOGIC
POSSIBLE CAUSE
NAVI control unit
FAIL-SAFE
The function of some multi-AV systems does not operate
DTC CONFIRMATION PROCEDURE
NOTE:
• The auto ACC function allows the accessory power supply for a certain period of time even after ignition
switch OFF. For this reason, when performing diagnosis, turn the ignition switch OFF and wait for 3 minutes
with the driver's door opened.
• The operation of the vehicle during standby may cause an accessory power supply.
1.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Turn ignition switch ON.
2.
Turn ignition switch OFF and wait for 3 minutes with the driver's door opened.
3.
Turn ignition switch ON and wait at least 30 seconds.
4.
Select “Self Diagnostic Result” mode of “MULTI AV” using CONSULT.
5.
Check DTC.
Is DTC U1229 detected?
YES
>> Proceed to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010714860
1.
PERFORM DTC CONFIRMATION PROCEDURE AGAIN
With CONSULT
1.
Turn ignition switch ON.
2.
Erase DTC.
3.
Perform DTC confirmation procedure again. Refer to
.
Is DTC U1229 detected again?
YES
>> Replace NAVI control unit. Refer to
AV-262, "Removal and Installation"
NO
>> INSPECTION END
DTC
Trouble diagnosis
(Trouble diagnosis contents)
Detecting condition
U1229
iPod CERTIFICATION
(iPod certification error)
NAVI control unit malfunction is detected.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст