Nissan X-Trail 32. Instruction — part 1475
LUGGAGE TRIM
INT-45
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
15. Disconnect power socket harness connector (luggage side lower finisher RH), and then remove luggage
side lower finisher.
16. Remove mounting bolts, and then remove front luggage side finisher bracket and rear luggage side fin-
isher bracket (without third seat).
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Visually check the clips for deformation and damage during installation. Replace with new ones if
necessary.
• Check in advance that clips and pawls are accurately aligned with the portions on body panel, and
then install by pressing in.
• Tighten second seat belt outer anchor mounting anchor bolts and third seat belt outer anchor
mounting anchor bolts to specified torque. Refer to
(second seat belt) or
(third seat belt).
LUGGAGE SIDE UPPER FINISHER
LUGGAGE SIDE UPPER FINISHER : Removal and Installation
INFOID:0000000010730564
CAUTION:
Never damage the body panel.
REMOVAL
1.
Remove luggage side lower finisher. Refer to
INT-43, "LUGGAGE SIDE LOWER FINISHER : Removal
2.
Remove second seat belt shoulder anchor bolt. Refer to
SB-17, "SEAT BELT RETRACTOR : Removal
3.
Remove third seat belt shoulder anchor bolt. Refer to
SB-21, "SEAT BELT RETRACTOR : Removal and
(with third seat).
4.
Remove luggage side upper finisher mounting bolt
.
5.
Remove luggage side upper finisher fixing clips using a remover
tool (A).
CAUTION:
Use a remover tool wrapped in tape (B).
JMJIB0108ZZ
: Clip
JMJIB0118ZZ
INT-46
< REMOVAL AND INSTALLATION >
LUGGAGE TRIM
6.
Disengage fixing metal clips according to numerical order 1
→
2 indicated by arrows as shown in the figure,
and then remove luggage side upper finisher.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Visually check clips and metal clips for deformation and damage during installation. Replace with
new ones if necessary.
• Check in advance that clips and metal clips are accurately aligned with the portions on body panel,
and then install by pressing in.
: Metal clip
: Vehicle front
JMJIA9841ZZ
BACK DOOR TRIM
INT-47
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
BACK DOOR TRIM
Exploded View
INFOID:0000000010730565
*1
: With automatic back door
*2
: Without automatic back door
Removal and Installation
INFOID:0000000010730566
CAUTION:
• When removing, always use a remover tool that is made of plastic to prevent damage to the parts.
• Never damage the back door panel.
REMOVAL
1.
Fully open back door.
Back door inner finisher
Back door assembly
automatic back door close switch fin-
isher
*1
Back door pull handle
Back door plate
Back door finisher lower cap
*2
: Clip
: Pawl
: Metal clip
: Vehicle front
JMJIA9762ZZ
INT-48
< REMOVAL AND INSTALLATION >
BACK DOOR TRIM
2.
Remove back door inner finisher fixing clips, and then remove
back door inner finisher.
3.
Remove back door pull handle.
a.
Apply protective tape (A) on the back door panel to protect from
damage.
b.
Disengage back door pull handle fixing pawls using a remover
tool (A), and then remove back door pull handle.
4.
Remove back door finisher lower cap (without automatic back door close switch).
a.
Apply protective tape (A) on the back door panel to protect from
damage.
: Clip
JMJIA9710ZZ
JMJIA9712ZZ
: Pawl
JMJIA9644ZZ
JMJIA9771ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст