Nissan X-Trail 32. Instruction — part 1474
LUGGAGE TRIM
INT-41
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
*1
: Without third seat
*2
: Without third seat and with temporary spare tire
*3
: With third seat
*4
: Without third seat and with full size spare tire
LUGGAGE REAR PLATE
LUGGAGE REAR PLATE : Removal and Installation
INFOID:0000000010730562
CAUTION:
Never damage the body panel.
REMOVAL
1.
Fully open back door.
2.
Remove rear luggage floor board center.
3.
Remove luggage rear plate mask.
a.
Apply protective tape (A) on luggage rear plate to protect it from
damage.
b.
Disengage luggage rear plate mask fixing pawls using a
remover tool (A), and then remove luggage rear plate mask.
4.
Remove back door weather-strip. Refer to the following.
• Type 1: Refer to
DLK-295, "BACK DOOR WEATHER-STRIP : Removal and Installation"
• Type 2: Refer to
DLK-603, "BACK DOOR WEATHER-STRIP : Removal and Installation"
• Type 3: Refer to
DLK-766, "BACK DOOR WEATHER-STRIP : Removal and Installation"
• Type 4: Refer to
DLK-908, "BACK DOOR WEATHER-STRIP : Removal and Installation"
: Clip
: Pawl
: Metal clip
: Vehicle front
,
,
,
: indicates that the part is connected at points with same symbol in actual vehicle.
JMJIA9649ZZ
: Pawl
JMJIA9642ZZ
INT-42
< REMOVAL AND INSTALLATION >
LUGGAGE TRIM
5.
Remove luggage rear plate fixing clips
.
6.
Apply protective tapes (A) on the body panel to protect it from
damage.
7.
Disengage luggage rear plate fixing pawls using a remover tool
(A).
8.
Remove luggage rear plate fixing clips using a remover tool (A).
CAUTION:
Use a remover tool wrapped in tape (B).
9.
Disengage fixing pawls, and then remove luggage rear plate.
JSJIA0106ZZ
JMJIA9643ZZ
: Pawl
JMJIB0102ZZ
: Clip
JMJIB0103ZZ
: Pawl
JMJIA9837ZZ
LUGGAGE TRIM
INT-43
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the clips for deformation and damage during installation. Replace with new ones if
necessary.
• Check in advance that clips and pawls are accurately aligned with the portions on body panel, and
then install by pressing in.
LUGGAGE SIDE LOWER FINISHER
LUGGAGE SIDE LOWER FINISHER : Removal and Installation
INFOID:0000000010730563
CAUTION:
Never damage the body panel.
REMOVAL
1.
Remove tonneau cover assembly.
2.
Remove second seat. Refer to
SE-54, "Removal and Installation"
3.
Remove third seat. Refer to
SE-70, "Removal and Installation"
(with third seat).
4.
Remove third seat striker. Refer to
SE-70, "Removal and Installation"
5.
Remove second seat belt outer anchor mounting anchor bolts.
6.
Remove third seat belt outer anchor mounting anchor bolts (with third seat).
7.
Remove luggage rear plate. Refer to
INT-41, "LUGGAGE REAR PLATE : Removal and Installation"
8.
Remove luggage room lamp. Refer to
INL-90, "Removal and Installation"
9.
Remove rope hook.
a.
Disengage fixing pawls using a remover tool (A), and then open
rope hook cover.
b.
Remove rope hook mounting bolt
, and then remove rope
hook.
: Pawl
JMJIA9839ZZ
JMJIB0104ZZ
INT-44
< REMOVAL AND INSTALLATION >
LUGGAGE TRIM
10. Remove luggage trim cap using a remover tool (A) (without third
seat).
CAUTION:
Use a remover tool wrapped in tape (B).
11. Remove luggage side lower finisher mounting bolts
(without
third seat).
12. Remove luggage side lower finisher rear end fixing clips using a
remover tool (A).
CAUTION:
Use a remover tool wrapped in tape (B).
13. Remove luggage side lower finisher front end fixing clips using a
remover tool (A).
CAUTION:
Use a remover tool wrapped in tape (B).
14. Disengage luggage side lower finisher fixing clips and pawls
according to numerical order 1
→
3 indicated by arrows as shown
in the figure.
: Pawl
JMJIA9838ZZ
JMJIB0105ZZ
: Clip
JMJIB0106ZZ
: Clip
JMJIB0107ZZ
: Clip
: Pawl
JMJIB0281ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст