Nissan X-Trail 32. Instruction — part 1801
SE-52
< REMOVAL AND INSTALLATION >
SECOND SEAT (SLIDING TYPE)
SECOND SEAT (SLIDING TYPE)
Exploded View
INFOID:0000000010713143
SECOND SEAT RH
JMJIA9708GB
Tether anchor cover
Upper board
Seatback board
Headrest
Headrest holder (lock)
Headrest holder (free)
Seatback frame
Seat control lever escutcheon
Seat control lever
Seat control cable 1
Screw cap
Seat cushion outside finisher outer
side
Hinge bracket
Seat cushion inside finisher outer
side
Cushion strap
*
Seat control cable 2
*
Lever unit outer side
*
Seat cushion spacer
Seat slide outer side
Front leg cover outer side
Towel bar
Front seat leg cover inner side
Seat slide inner side
Lever unit inner side
*
Seat cushion silencer
Seat cushion pad
Seat cushion trim
SECOND SEAT (SLIDING TYPE)
SE-53
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
*: If equipped
SECOND SEAT LH
Seatback pad
Seatback trim
Seatback silencer
Reclining device cover
Spring
Seat cushion frame
Seat cushion inside finisher inner
side rear
Reclining spring
Seat cushion outside finisher inner
side
Seat cushion inside finisher inner
side front
Rear leg cover outer side
Rear leg cover inner side
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JMJIA9709GB
SE-54
< REMOVAL AND INSTALLATION >
SECOND SEAT (SLIDING TYPE)
*: If equipped
Removal and Installation
INFOID:0000000010713144
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
REMOVAL
1.
Remove headrest.
2.
Disengage leg cover fixing pawls, and then remove leg covers.
• second seat RH
Cup holder
Headrest holder (lock)
Headrest holder (free)
Center headrest
Armrest silencer
Armrest trim
Armrest pad
Armrest frame
Armrest strap
Armrest bracket outer cover
Armrest bracket inner cover
Seatback side trim
Seatback side pad
Seat cushion trim
Seat cushion pad
Seat cushion silencer
Rear leg cover inner side
Lever unit inner side
*
Seat slide inner side
Front leg cover inner side
Towel bar
Front leg cover outer side
Seat cushion spacer
Seat slide outer side
Lever unit outer side
*
Rear leg cover outer side
Seat control cable 2
*
Cushion strap
*
Screw cap
Seat cushion outside finisher outer
side
Hinge bracket
Seat cushion inside finisher outer
side
Seat control cable 1
Seat control lever
Seat control lever escutcheon
Seatback board
Upper board
Tether anchor cover
Seat belt guide A
Seat belt guide B
Headrest
Seatback silencer
Seatback trim
Seatback pad
Armrest bracket
Seatback frame
Bush
Bush
Seat cushion outside finisher inner
side
Seat cushion inside finisher inner
side
Seat cushion center finisher outer
Seat cushion center finisher inner
Seat cushion frame
Reclining spring
Spring
Reclining device cover
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: Pawl
: Vehicle front
JMJIA9650ZZ
SECOND SEAT (SLIDING TYPE)
SE-55
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
• second seat LH
3.
Remove seat fixing bolts.
4.
Disconnect seat belt harness connector (if equipped).
5.
Remove seat from vehicle.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
• When installing, tighten fixing bolts according to the numeri-
cal order 1
→
4 as shown in the figure, starting from front inner
fixing bolt.
ARMREST
ARMREST : Removal and Installation
INFOID:0000000010713145
REMOVAL
CAUTION:
When removing, always use a remover tool that is made of plastic to prevent damage to the parts.
1.
Remove seatback board LH.
a.
Disengage tether anchor cover fixing pawls, and then remove
tether anchor (if equipped).
: Pawl
: Vehicle front
JMJIA9651ZZ
JMJIA9652ZZ
: Pawl
JMJIA9653ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст