Nissan X-Trail 32. Instruction — part 2044
TM-134
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
TRANSAXLE ASSEMBLY
20. Rotate striking lever of striking rod as shown in the figure. Then
rotate reverse fork rod to a position where bracket of reverse
fork rod does not interfere with striking lever of striking rod.
21. Pull out reverse shift fork and reverse fork rod.
22. Remove retaining pin of 5th-6th shift fork
using a pin punch
(commercial service tool).
23. Remove retaining pin of 3rd-4th shift fork
using a pin punch
(commercial service tool).
24. Pull out 3rd-4th fork rod.
25. Pull out 5th-6th shift fork
and 5th-6th fork rod
.
26. Pull out 3rd-4th shift fork
.
PCIB1851E
: 5th-6th fork rod
PCIB1852E
: 3rd-4th fork rod
PCIB1853E
PCIB1854E
PCIB1855E
TRANSAXLE ASSEMBLY
TM-135
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
27. Remove retaining pin of 1st-2nd shift fork
using a pin punch
(commercial service tool).
28. Pull out 1st-2nd shift fork and 1st-2nd fork rod.
29. Remove striking rod assembly
.
30. Remove gear components from clutch housing, as per the fol-
lowing procedure.
a.
Remove a set of input shaft assembly, mainshaft assembly, and
reverse idler gear assembly by tapping the tip of input shaft from
the back of the clutch housing with a plastic hammer.
CAUTION:
Always withdraw mainshaft straight out. Failure to do so
can damage resin oil channel on clutch housing side.
b.
Remove final drive assembly.
31. Remove magnet from clutch housing.
32. Remove mainshaft bearing retainer and then mainshaft front
bearing from clutch housing using the puller (A) (SST:
KV381054S0).
CAUTION:
Never damage clutch housing, mainshaft front bearing, and
oil channel.
33. Remove oil channel from clutch housing.
: 1st-2nd fork rod
PCIB1856E
PCIB1857E
SCIA0964E
PCIB1859E
JSDIA6488ZZ
TM-136
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
TRANSAXLE ASSEMBLY
34. Remove differential side bearing outer race (clutch housing
side) from clutch housing using the puller (A) (SST:
KV381054S0).
CAUTION:
Never damage clutch housing and differential side bearing
outer race.
35. Remove input shaft oil seal from clutch housing, using oil seal
remover (commercial service tool).
CAUTION:
Never damage clutch housing.
36. Remove differential side oil seal from clutch housing, using oil
seal remover (commercial service tool).
CAUTION:
Never damage clutch housing.
ASSEMBLY
JSDIA6489ZZ
SCIA0398E
PCIB1874E
TRANSAXLE ASSEMBLY
TM-137
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
1.
Install differential side oil seal
to clutch housing using the drift
(A) (SST: ST33400001).
CAUTION:
• Never reuse differential side oil seal.
• Apply multi-purpose grease onto oil seal lip.
• Never incline differential side oil seal.
• Never damage clutch housing.
2.
Install input shaft oil seal
to clutch housing using the drift (A)
(SST: ST35321000).
CAUTION:
• Never reuse input shaft oil seal.
• Apply multi-purpose grease onto oil seal lip.
• Never incline input shaft oil seal.
• Never damage clutch housing.
3.
Install differential side bearing outer race (clutch housing side) to
clutch housing using the drift (A) (SST: ST30720000).
CAUTION:
Replace differential side bearing and differential side bear-
ing outer race as a set.
Dimension (H)
:
−
0.5 – 0.5 mm (
−
0.020 – 0.020 in)
PCIB1864E
Dimension (H)
: 1.1 – 2.1 mm (0.043 – 0.083 in)
PCIB1814E
JSDIA6490ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст