Nissan X-Trail 32. Instruction — part 2043
TM-130
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
TRANSAXLE ASSEMBLY
2.
Remove plug
with O-ring from clutch housing.
3.
Remove plug
with gasket from transaxle case.
4.
Remove neutral position switch
from transaxle case.
5.
Remove back-up lamp switch
and plunger from transaxle
case.
CAUTION:
Never lose plunger.
6.
Remove air breather tube
from transaxle case.
JSDIA6147ZZ
JSDIA6483ZZ
JSDIA6484ZZ
JSDIA6485ZZ
JSDIA6486ZZ
TRANSAXLE ASSEMBLY
TM-131
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
7.
Remove guide bolt from transaxle case.
8.
Remove retaining pin using a pin punch (commercial service
tool) and then remove select lever from transaxle case.
9.
Remove transaxle case mounting bolts.
10. Remove bore plug from transaxle case.
CAUTION:
• Never damage transaxle case.
• Access bore plug from cutout
of transaxle case when
removing.
11. Remove transaxle case, as per the following procedure.
PCIB1836E
PCIB1837E
PCIB1838E
PCIB1839E
TM-132
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
TRANSAXLE ASSEMBLY
a.
Expand snap ring at mainshaft rear bearing accessing from the
bore plug hole. Then pull up transaxle case from clutch housing
until snap ring comes off.
b.
While rotating shift lever (outer)
in the direction of the arrow in
the figure, remove transaxle case from clutch housing.
CAUTION:
Never drop each adjusting shim.
NOTE:
Make sure to hold shift lever (outer) in the position shown in the
figure. Otherwise transaxle case cannot be removed from clutch
housing.
12. Remove oil gutter A
and oil gutter B
from transaxle case.
13. Remove snap ring from transaxle case.
14. Remove retaining pin using a pin punch (commercial service
tool) and then remove shift lever (outer) and shift lever (inner)
from transaxle case.
PCIB1840E
JPDIC0140ZZ
: Tab of oil gutter
PCIB1841E
PCIB1842E
PCIB1844E
TRANSAXLE ASSEMBLY
TM-133
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
15. Remove differential side bearing outer race (transaxle case
side) from transaxle case using the puller (A) (SST:
KV381054S0) and then remove differential side bearing adjust-
ing shim from transaxle case.
CAUTION:
Never damage transaxle case and differential side bearing
outer race.
16. Remove differential side oil seal from transaxle case, using oil
seal remover (commercial service tool).
CAUTION:
Never damage transaxle case.
17. Remove shift lever oil seal
and striking rod oil seal
from
transaxle case, using oil seal remover (commercial service tool).
CAUTION:
Never damage transaxle case.
18. Remove striking rod shim
, striking rod adjusting shim
,
mainshaft rear bearing adjusting shim
, input shaft rear bear-
ing adjusting shim
, and reverse idler gear adjusting shim
.
19. Remove retaining pin of reverse shift fork
using a pin punch
(commercial service tool).
JSDIA6487ZZ
SCIA0397E
PCIB1846E
PCIB1858E
: Reverse fork rod
PCIB1850E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст