Nissan X-Trail 32. Instruction — part 1669
PCS-46
< WIRING DIAGRAM >
[IPDM E/R]
IPDM E/R
JRMWF4078GB
PCS
ADDITIONAL SERVICE WHEN REPLACING IPDM E/R
PCS-47
< BASIC INSPECTION >
[IPDM E/R]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
BASIC INSPECTION
ADDITIONAL SERVICE WHEN REPLACING IPDM E/R
Description
INFOID:0000000010741713
After replaced IPDM E/R, it is necessary to perform control unit configuration and height sensor initialize (For
LED headlamp models) with CONSULT.
BEFORE REPLACEMENT
When replacing IPDM E/R, save or print current vehicle specification with CONSULT configuration before
replacement.
NOTE:
If “Before Replace ECU” of “Read/Write Configuration” cannot be used, use the “Instruction Configuration” after
replacing IPDM E/R.
AFTER REPLACEMENT
CAUTION:
• When replacing IPDM E/R, always perform “Read/Write Configuration” or “Instruction Configuration”
with CONSULT. Or not doing so, IPDM E/R control function does not operate normally.
• Never perform “Read / Write Configuration” or “Instruction Configuration” except for new IPDM E/R or
the control function may not operate normally.
Work Procedure
INFOID:0000000010741714
1.
SAVING VEHICLE SPECIFICATION (IPDM E/R)
CONSULT Configuration
Perform “Before Replace ECU” of “Read / Write Configuration” to save or print current vehicle specification.
Refer to
NOTE:
If “Before Replace ECU” of “Read/Write Configuration” cannot be used, use the “Instruction Configuration” after
replacing IPDM E/R.
>> GO TO 2.
2.
REPLACE IPDM E/R
Replace IPDM E/R. Refer to
PCS-60, "Removal and Installation"
.
>> GO TO 3.
3.
WRITING VEHICLE SPECIFICATION (IPDM E/R)
CONSULT Configuration
Perform “After Replace ECU” of “Read/Write Configuration” or “Instruction Configuration” to write vehicle specifi-
cation. Refer to
>> GO TO 4.
4.
CHECK HEADLAMP TYPE
Check headlamp type.
LED headlamp>>GO TO 5.
Halogen headlamp>>WORK END
5.
HEIGHT SENSOR INITIALIZE
Perform height sensor initialize. Refer to
.
>> WORK END
PCS-48
< BASIC INSPECTION >
[IPDM E/R]
CONFIGURATION (IPDM E/R)
CONFIGURATION (IPDM E/R)
Description
INFOID:0000000010741715
There is no vehicle specification in new IPDM E/R, so the vehicle specification needs to be written in IPDM E/
R with CONSULT.
Configuration has three functions as follows.
CAUTION:
• When replacing IPDM E/R, always perform “Read/Write Configuration” or “Instruction Configuration”
with CONSULT. Or not doing so, IPDM E/R control function does not operate normally.
• Never perform “Read / Write Configuration” or “Instruction Configuration” except for new IPDM E/R or
the control function may not operate normally.
Work Procedure
INFOID:0000000010741716
1.
WRITING MODE SELECTION
CONSULT Configuration
Select “CONFIGURATION” of IPDM E/R.
When writing saved data>>GO TO 2.
When writing instructionly>>GO TO 3.
2.
PERFORM “WRITE CONFIGURATION”
CONSULT Configuration
1.
Select “READ/WRITE CONFIGURATION”.
2.
Select “After Replace ECU”.
>> GO TO 4.
3.
PERFORM “MANUAL CONFIGURATION”
CONSULT Configuration
1.
Select “MANUAL CONFIGURATION”.
2.
Identify the correct model and configuration list. Refer to
.
CAUTION:
• Thoroughly read and understand the vehicle specification. ECU control may not operate nor-
mally if the setting is not correct.
• Make sure to select “SETTING” even if the indicated configuration of brand new IPDM E/R is
same as the desirable configuration. If not, configuration which is set automatically by selecting
vehicle model cannot be memorized
3.
Sets the displayed item and then select “NEXT”.
NOTE:
If item is not displayed, select “NEXT”.
4.
Check that the configuration has been successfully written and touch “End”.
>> GO TO 4.
4.
OPERATION CHECK
Confirm that each function controlled by IPDM E/R operates normally.
>> WORK END
Function
Description
READ/WRITE CON-
FIGURATION
Before Replace ECU
• Reads the vehicle configuration of current BCM.
• Saves the read vehicle configuration.
After Replace ECU
Writes the vehicle configuration with saved data.
MANUAL CONFIGURATION
Writes the vehicle configuration with instruction selection.
PCS
CONFIGURATION (IPDM E/R)
PCS-49
< BASIC INSPECTION >
[IPDM E/R]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Configuration list
INFOID:0000000010741717
CAUTION:
Check vehicle specifications before servicing.
MANUAL SETTING ITEM
NOTE
System
Item
Setting value
IPDM-E
Data part number
284B7-4CB1A
All of the following are satisfied
• MR20 engine
• M/T
• Headlamp aiming control system (instruction)
• Halogen headlamp
• Without Intelligent Key system
• Without stop/start system
IPDM-E
Data part number
284B7-4CB1C
All of the following are satisfied
• MR20 engine
• CVT
• Headlamp aiming control system (instruction)
• Halogen headlamp
• With Intelligent Key system
• Without stop/start system
IPDM-E
Data part number
284B7-4CB1E
All of the following are satisfied
• MR20 engine
• CVT
• Headlamp aiming control system (instruction)
• Halogen headlamp
• Without Intelligent Key system
• Without stop/start system
IPDM-E
Data part number
284B7-4CB2B
All of the following are satisfied
• MR20 engine
• CVT
• Headlamp aiming control system (auto)
• LED headlamp
• With Intelligent Key system
• Without stop/start system
IPDM-E
Data part number
284B7-4CB2E
All of the following are satisfied
• QR25 engine
• CVT
• Headlamp aiming control system (instruction)
• Halogen headlamp
• With Intelligent Key system
• Without stop/start system
IPDM-E
Data part number
284B7-4CB3B
All of the following are satisfied
• QR25 engine
• CVT
• Headlamp aiming control system (auto)
• LED headlamp
• With Intelligent Key system
• Without stop/start system
IPDM-E
Data part number
284B7-4CB3D
All of the following are satisfied
• R9M engine
• M/T
• Headlamp aiming control system (instruction)
• Halogen headlamp
• Without Intelligent Key system
• With stop/start system
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст