Nissan X-Trail 32. Instruction — part 2056
TM-182
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
TRANSAXLE ASSEMBLY
a.
Temporarily install snap ring of mainshaft rear bearing into tran-
saxle case.
CAUTION:
Never reuse snap ring.
b.
Install dummy adjusting shim
to mainshaft assembly.
c.
With shift lever (outer)
held in the position shown in the figure,
temporarily assemble transaxle case to clutch housing.
CAUTION:
Never damage striking rod oil seal.
NOTE:
Make sure to hold shift lever (outer) in the position shown in the
figure. Otherwise transaxle case cannot be installed to clutch
housing.
d.
While rotating shift lever (outer)
in the direction of the arrow
shown in the figure, assemble transaxle case to clutch housing.
NOTE:
The shift lever (inner) can be inserted into the groove of striking
rod.
e.
Accessing from the bore plug hole, expand snap ring at main-
shaft rear bearing so that the ring catches the periphery of main-
shaft rear bearing.
f.
Temporarily tighten transaxle case mounting bolts.
PCIB1842E
PCIB1826E
JPDIC0140ZZ
: Shift lever (inner)
JPDIC0141ZZ
PCIB1840E
TRANSAXLE ASSEMBLY
TM-183
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2.
Shift the shift lever (outer)
to 2nd gear position.
NOTE:
• The 2nd gear position is attained when shift lever (outer) is in
the position shown in the figure.
• When transaxle is shifted to the 2nd gear position, mainshaft
assembly
is
lifted.
3.
Seat snap ring in the groove on mainshaft rear bearing. If snap ring is not seated in the groove on main-
shaft rear bearing, remove transaxle case and repeat the procedure 1 from step c.
4.
Shift the shift lever (outer) to 1st gear position, and then shift it to 2nd gear position. Repeat 3 times.
NOTE:
• The mainshaft rear bearing position will be stabilized by shifting between 1st gear position and 2nd gear
position alternately.
• The 1st gear position is attained when shift lever (outer)
is
in the position shown in the figure.
• When transaxle is shifted to the 1st gear position, mainshaft
assembly
is
declined.
PCIB1809E
PCIB1923E
PCIB1881E
PCIB1934E
TM-184
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
TRANSAXLE ASSEMBLY
5.
Set the dial indicator (A) to dummy adjusting shim
through the
bore plug mounting hole.
6.
Shift the shift lever (outer)
to 2nd gear position
, and then
rotate it in the direction of the arrow
in the figure until it stops.
Using this position as the reference point, measure the amount
of movement when shifting shift lever (outer) to 1st gear position
and rotating it in the direction of the arrow
in the figure until
it stops. This measurement is the (M) dimension.
7.
When measurement (M) is 0 – 0.06 mm (0 – 0.0024 in), adjust-
ment terminates, and the dummy adjusting shim becomes regu-
lar adjusting shim. Select adjusting shim from the computed
expressions when measurement (M) is over 0.06 mm (0.0024
in).
: Mainshaft rear bearing
: Snap ring
M
: Distance between dummy adjusting shim on mainshaft
rear bearing end face and transaxle case end face
PCIB1827E
PCIB1935E
INPUT SHAFT AND GEAR
TM-185
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
INPUT SHAFT AND GEAR
Exploded View
INFOID:0000000010957984
CAUTION:
Input shaft front bearing
Input shaft
3rd needle bearing
3rd input gear
3rd inner baulk ring
3rd synchronizer cone
3rd outer baulk ring
3rd-4th spread spring
3rd-4th shifting insert
3rd-4th synchronizer hub
4th baulk ring
3rd-4th coupling sleeve
4th input gear bushing
4th needle bearing
4th input gear
Thrust washer
5th input gear bushing
5th needle bearing
5th input gear
5th baulk ring
5th-6th spread spring
5th-6th shifting insert
5th-6th synchronizer hub
5th-6th coupling sleeve
6th baulk ring
6th input gear
6th needle bearing
6th input gear bushing
Snap ring
Input shaft rear bearing
Oil channel
Input shaft rear bearing adjusting
shim
Retaining pin
Reverse idler shaft
Thrust needle bearing
Reverse idler gear needle bearing
Reverse insert spring
Reverse idler gear (front)
Reverse baulk ring
Reverse coupling sleeve
Reverse idler gear (rear)
Reverse idler gear adjusting shim
: Always replace after every disassembly.
: Select with proper thickness.
: Replace the parts as a set.
PCIB1888E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст