Nissan X-Trail 32. Instruction — part 2054
TM-174
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
TRANSAXLE ASSEMBLY
d.
Apply recommended sealant to mating surface of clutch housing
as shown in the figure.
• For sealant to use, refer to
CAUTION:
• Remove old sealant adhering to the mounting surfaces.
Also remove any moisture, oil, or foreign material adher-
ing to both mounting surfaces.
• Apply sealant so as not to break the bead.
• The width of sealant bead is 1 – 2 mm (0.04 – 0.08 in).
• The height of sealant bead is 0.4 – 1 mm (0.016 – 0.04 in).
• The overlap length of both ends of sealant bead is 3 – 5
mm (0.12 – 0.20 in).
e.
With shift lever (outer)
held in the position shown in the figure,
temporarily assemble transaxle case to clutch housing.
CAUTION:
Never damage striking rod oil seal.
NOTE:
Make sure to hold shift lever (outer) in the position shown in the
figure. Otherwise transaxle case cannot be installed to clutch
housing.
f.
While rotating shift lever (outer)
in the direction of the arrow in
the figure, assemble transaxle case to clutch housing.
NOTE:
The shift lever (inner) can be inserted into the groove of striking
rod.
g.
Accessing from the bore plug hole, expand snap ring at main-
shaft rear bearing so that the ring catches the periphery of main-
shaft rear bearing.
h.
Temporarily tighten transaxle case mounting bolts.
i.
Shift the shift lever (outer)
to 2nd gear position.
NOTE:
• The 2nd gear position is attained when shift lever (outer) is in
the position shown in the figure.
PCIB1807E
JPDIC0140ZZ
: Shift lever (inner)
JPDIC0141ZZ
PCIB1840E
PCIB1809E
TRANSAXLE ASSEMBLY
TM-175
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• When transaxle is shifted to the 2nd gear position, mainshaft
assembly
is
lifted.
j.
Seat snap ring in the groove on mainshaft rear bearing. If snap
ring is not seated in the groove on mainshaft rear bearing,
remove transaxle case and repeat the procedure from step d.
k.
Tighten transaxle case mounting bolts to the specified torque.
l.
Shift the shift lever (outer)
to neutral position.
NOTE:
The neutral position is attained when shift lever (outer) is in the
position shown in the figure.
32. Install bore plug to transaxle case using the drift (A) (SST:
ST33061000).
CAUTION:
Never reuse bore plug.
33. Install select lever to transaxle case and then install retaining pin
to select lever.
CAUTION:
• Never reuse retaining pin.
• Assemble retaining pin from the direction shown by the
arrow in the figure until it becomes flush with the end sur-
face of select lever.
PCIB1923E
PCIB1838E
PCIB1930E
JSDIA6492ZZ
PCIB1837E
TM-176
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
TRANSAXLE ASSEMBLY
34. Install guide bolt, as per the following procedure.
a.
Shift the shift lever (outer) and select lever to neutral position.
b.
Visually confirm from the guide bolt mounting hole
that the
lever is securely set to neutral position. If it is not in the neutral
position, repeat the procedure from step a.
CAUTION:
The guide bolt
may damage striking rod by running into
outer-groove points, if guide bolt is tightened in the state of
shown in the figure.
c.
Check continuity between terminals of neutral position switch to
confirm it in the neutral position. If it is not in the neutral position,
repeat the procedure from step a. Refer to
d.
Install guide bolt to transaxle case and then tighten guide bolt to
the specified torque.
CAUTION:
Never reuse guide bolt.
35. Apply recommended sealant to threads of neutral position
switch
. Then install it to transaxle case and tighten to the
specified torque.
• For sealant to use, refer to
CAUTION:
Remove old sealant and oil adhering to threads.
: Neutral position
: Except neutral position
: Groove of striking rod
PCIB1890E
PCIB1836E
JSDIA6484ZZ
TRANSAXLE ASSEMBLY
TM-177
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
36. Apply recommended sealant to threads of back-up lamp switch
. Then install it with plunger to transaxle case and tighten to
the specified torque.
• For sealant to use, refer to
CAUTION:
Remove old sealant and oil adhering to threads.
37. Install air breather tube
to transaxle case.
CAUTION:
• Never reuse air breather tube.
• Assemble air breather tube until its collar element con-
tacts with transaxle case.
38. Install gasket onto plug and then install them into transaxle
case. Tighten plug to the specified torque.
CAUTION:
Never reuse gasket.
39. Install gasket onto drain plug and then install them into clutch
housing. Tighten drain plug to the specified torque.
CAUTION:
Never reuse gasket.
40. Install gasket onto filler plug and then install them into transaxle
case. Tighten filler plug to the specified torque.
CAUTION:
• Never reuse gasket.
• After gear oil is filled, tighten filler plug to specified
torque.
JSDIA6485ZZ
JSDIA6486ZZ
PCIB1865E
JPDIC0073ZZ
JPDIC0047ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст