Nissan X-Trail 32. Instruction — part 2214
DIAGNOSIS AND REPAIR WORK FLOW
WT-29
< BASIC INSPECTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
YES
>> GO TO 8.
NO
>> Perform diagnosis procedure of “TIRE PRESSURE SENSOR ID REGISTRATION CANNOT BE
. And then GO TO 8.
8.
CHECK LOW TIRE PRESSURE WARNING LAMP STATES (2)
1.
Adjust the tire pressure for all wheels specified to the value. Refer to
.
2.
Perform TPMS reset operation. Refer to
3.
Check states of low tire pressure warning lamp in combination meter when ignition switch is turned ON.
Does low tire pressure warning lamp turn ON for 1 second and then turn OFF?
YES
>> Explain to the customer that this is TPMS normal operation, and GO TO 13.
NO
>> GO TO 9.
9.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “AIR PRESSURE MONITOR”.
Is DTC detected?
YES
>> Record or print self-diagnosis results and freeze frame data (FFD). GO TO 10.
NO
>> GO TO 11.
10.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
Perform DTC CONFIRMATION PROCEDURE for the detected DTC, and then check that DTC is detected
again.
Is DTC detected?
YES
>> GO TO 12.
NO
>> Check harness and connectors based on the information obtained by interview and repair or
replace error-detected parts. Refer to
GI-44, "Intermittent Incident"
. GO TO 13.
11.
CONFIRM THE SYMPTOM
Perform symptom diagnosis. refer to
>> Repair or replace error-detected parts. GO TO 13.
12.
DIAGNOSIS PROCEDURE
Perform DTC Diagnosis Procedure.
>> Repair or replace error-detected parts. GO TO 13.
13.
FINAL CHECK
Recheck the symptom and check that the symptom is not reproduced on the same conditions.
Is the symptom reproduced?
YES
>> GO TO 3.
NO
>> INSPECTION END
WT-30
< BASIC INSPECTION >
TIRE PRESSURE SENSOR ID REGISTRATION
TIRE PRESSURE SENSOR ID REGISTRATION
Description
INFOID:0000000010715071
This procedure must be performed:
• After replacement of a tire pressure sensor or BCM.
• After replacement of tire or road wheel.
NOTE:
ID registration is unnecessary if there are no change in the positions of each wheels (tire pressure sensors)
before wheel removal and after wheel installation.
• After performing tire rotation.
Work Procedure
INFOID:0000000010715072
1.
TIRE PRESSURE SENSOR ID REGISTRATION PROCEDURE
CAUTION:
To perform ID registration, observe the following points:
• Never register ID in a place where radio waves are interfered (e.g. radio tower).
• Never register ID in a place close to vehicles including TPMS.
NOTE:
Refer to the manufacture operating instructions for how to use the tire pressure sensor activation tool
[KV48105501 or NI-4032].
With CONSULT
1.
Turn the ignition switch ON.
2.
Display the “WORK SUPPORT” screen and select “ID REGIST”.
3.
Select the start button on the “ID REGIST” screen.
4.
Contact the tire pressure sensor activation tool [KV48105501 or
NI-4032]
to the side of the tire at the location to the tire pres-
sure sensor.
5.
Press the registration button and wait until the hazard warning
lamp blinks twice.
CAUTION:
Perform the ID registration procedure starting from the
vehicle front left wheel, then repeat the procedure in the
order of the front right wheel, rear right wheel, and rear left
wheel.
6.
When ID registration is completed, check the following pattern at each wheel.
7.
After the ID registration procedure for all wheels is completed, press “End” to end ID registration, and
check that ID registration for all wheels is completed.
Is the check result normal?
YES
>> ID registration END.
NO
>> Refer to
.
NNEIC0020ZZ
Sequence
ID registration position
Turn signal lamp
CONSULT
1
Front left wheel
2 blinks
“Yet (red)”
↓
“Done (green)”
2
Front right wheel
3
Rear right wheel
4
Rear left wheel
CONFIGURATION (TIRE PRESSURE MONITORING SYSTEM)
WT-31
< BASIC INSPECTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
CONFIGURATION (TIRE PRESSURE MONITORING SYSTEM)
Work Procedure
INFOID:0000000010715073
CAUTION:
• Use “Instruction Configuration” only when “TYPE ID” of BCM cannot be read.
• After configuration, perform the following:
- Turn the ignition switch from OFF to ON and check that the low tire pressure warning lamp turns
OFF after staying illuminated for approximately two seconds.
- Perform tire pressure sensor ID registration. Refer to
• If an error occurs during configuration, start over from the beginning.
1.
CHECKING TYPE ID (1)
Use FAST (service parts catalogue) to search BCM of the parts number and find “Type ID”.
Is “Type ID” displayed?
YES
>> Print out “Type ID” and GO TO 2.
NO
>> “Configuration” is not required for BCM. Replace in the usual manner. Refer to
.
2.
CHECKING TYPE ID (2)
CONSULT Configuration
1.
Select “AIR PRESSURE MONITOR”
2.
Select “Before Replace ECU” of “Read/Write Configuration”.
3.
Check that “Type ID” is displayed on the CONSULT screen.
Is “Type ID” displayed?
YES
>> GO TO 3.
NO
>> GO TO 7.
3.
VERIFYING TYPE ID (1)
CONSULT Configuration
Compare a “Type ID” displayed on the CONSULT screen with the one searched by using FAST (service parts
catalogue) to check that these “Type ID” agree with each other.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.
>> GO TO 4.
4.
SAVING TYPE ID
CONSULT Configuration
Save “Type ID” on CONSULT.
>> GO TO 5.
5.
REPLACING BCM (1)
BCS-121, "Removal and Installation"
.
>> GO TO 6.
6.
WRITING (AUTOMATIC WRITING)
CONSULT Configuration
1.
Select “After Replace ECU” of “Re/programming, Configuration” or that of “Read / Write Configuration”.
2.
Select the “Type ID” agreeing with the one stored on CONSULT and the one searched by using FAST
(service parts catalogue) to write the “Type ID” into the BCM.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.
>> GO TO 9.
WT-32
< BASIC INSPECTION >
CONFIGURATION (TIRE PRESSURE MONITORING SYSTEM)
7.
REPLACING BCM (2)
Replace BCM. Refer to
BCS-121, "Removal and Installation"
.
>> GO TO 8.
8.
WRITING (MANUAL WRITING)
CONSULT Configuration
1.
Select “Instruction Configuration”.
2.
Select the “Type ID” searched by using FAST (service parts catalogue) to write the “Type ID” into the
BCM.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.
>> GO TO 9.
9.
VERIFYING TYPE ID (2)
Compare “Type ID” written into the BCM with the one searched by using FAST (service parts catalogue) to
check that these “Type ID” agree with each other.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.
>> GO TO 10.
10.
CHECKING LOW TIRE PRESSURE WARNING LAMP
1.
Turn the ignition switch OFF.
2.
Turn the ignition switch ON and check that the low tire pressure warning lamp turns OFF after staying illu-
minated for approximately two seconds.
CAUTION:
Never start the engine.
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> Perform the self-diagnosis of “AIR PRESSURE MONITOR”. Refer to
.
11.
PERFORMING SUPPLEMENTARY WORK
1.
Adjust the tire pressure to the specified value. Refer to
2.
Perform tire pressure sensor ID registration. Refer to
.
3.
Perform the self-diagnosis of all systems.
4.
Erase self-diagnosis results.
5.
Perform TPMS reset operation. Refer to
>> End of work.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст