Nissan X-Trail 32. Instruction — part 364
DAS
CHASSIS CONTROL MODULE
DAS-197
< ECU DIAGNOSIS INFORMATION >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
ECU DIAGNOSIS INFORMATION
CHASSIS CONTROL MODULE
Reference Value
INFOID:0000000010721696
CONSULT DATA MONITOR STANDARD VALUE
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Monitor item
Condition
Reference value in normal operation
IGN VOLT
Ignition switch ON
10
−
16 V
CONTROL MODULE MALF
When chassis control module is normal
Off
When chassis control module malfunction is detected
On
CAN DIAG STATUS
When diagnosis of CAN communication malfunction is
detected
Off
When diagnosis of CAN communication is normal
On
STP LAMP OFF RELAY 1
Displayed but not used
—
STP LAMP OFF RELAY 2
Displayed but not used
—
ESS RELAY
Displayed but not used
—
VEHICLE SPEED
Vehicle stopped
0 km/h
Vehicle driving
*
Almost same reading as speedometer
(Within
±
10%)
FR WHEEL SPEED
Vehicle stopped
0 rpm
Vehicle driving
*
Increases according to vehicle speed
FL WHEEL SPEED
Vehicle stopped
0 rpm
Vehicle driving
*
Increases according to vehicle speed
RR WHEEL SPEED
Vehicle stopped
0 rpm
Vehicle driving
*
Increases according to vehicle speed
RL WHEEL SPEED
Vehicle stopped
0 rpm
Vehicle driving
*
Increases according to vehicle speed
STEERING ANG SENSOR
When vehicle driving straight
0
±
3.5 deg
When steering wheel is steered to RH by 90
°
Approx. +90 deg
When steering wheel is steered to LH by 90
°
Approx.
−
90 deg
DECEL G SENSOR
Vehicle stopped
Approx. 0 G
When during acceleration
Positive value
When during deceleration
Negative value
SIDE G SENSOR
Vehicle stopped
Approx. 0 G
When right turn
Negative value
When left turn
Positive value
YAW RATE SENSOR
Vehicle stopped
Approx. 0 deg/s
When right turn
Negative value
When left turn
Positive value
ACCELE PEDAL POSITION
When accelerator pedal is released
0%
When accelerator pedal is depressed
0
−
100%
DAS-198
< ECU DIAGNOSIS INFORMATION >
[CHASSIS CONTROL]
CHASSIS CONTROL MODULE
THROTTLE CONTROL
When electric throttle control actuator is normal
NORMAL
When electric throttle control actuator does not
achieve the requirement (measured value is inaccu-
rate)
INCORR
When electric throttle control actuator does not
achieve the requirement (temporary prevention)
PREV
When electric throttle control actuator does not
achieve the requirement (impossible)
INPOSSI
SHIFT POSITION
Displayed but not used
—
BRAKE SWITCH 2
When brake pedal is not depressed
Off
When brake pedal is depressed
On
BRAKE SWITCH 1
When brake pedal is depressed
Off
When brake pedal is not depressed
On
STOP LAMP SW
When brake pedal is depressed
ACT
When brake pedal is not depressed
INACT
PRESS SENSOR
When brake pedal is not depressed
Approx. 0 bar
When brake pedal is depressed
0
−
255 bar
ABS
When ABS function is normal
NORMAL
When ABS function malfunction is detected
ABNOR
ABS MALF
When ABS function is normal
NORMAL
When ABS function malfunction is detected
ABNOR
EBD
When EBD function is normal
NORMAL
When EBD function malfunction is detected
ABNOR
ACCELE PEDAL MALF
When accelerator pedal is normal
NORMAL
When accelerator pedal malfunction is detected
ABNOR
TCS
When TCS function is normal
NORMAL
When TCS function malfunction is detected
ABNOR
TCS MALF
When TCS function is normal
NORMAL
When TCS function malfunction is detected
ABNOR
VDC
When VDC function is normal
NORMAL
When VDC function malfunction is detected
ABNOR
VDC MALF
When VDC function is normal
NORMAL
When VDC function malfunction is detected
ABNOR
PARKING BRAKE
Displayed but not used
—
DRV TRQ CTRL MODE
When correction coefficients are initialized
INITIAL
When correction is executed
NORMAL
When correction is stopped (computing is impossible)
STOP 1
When correction is stopped (computing is possible)
STOP 2
When correction is limited
LIMIT 1
When correction is prohibited
PROHIBI
DRV TRQ CTRL PERMIS 1
When correction is permitted (basic requirement)
PERMIS
When correction is not permitted (basic requirement)
NO PER
DRV TRQ CTRL PERMIS 2
When correction is permitted (system requirement)
PERMIS
When correction is not permitted (system require-
ment)
NO PER
Monitor item
Condition
Reference value in normal operation
DAS
CHASSIS CONTROL MODULE
DAS-199
< ECU DIAGNOSIS INFORMATION >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
DRV TRQ CTRL STOP
When correction is requested to stop
REQ
When correction is not requested to stop
NO REQ
DRV TRQ CTRL PROHIBIT
When prohibition of correction is requested
REQ
When prohibition of correction is not requested
NO REQ
AEB STATUS
When active engine brake (brake control) function is
active
On
When active engine brake (brake control) function is
inactive.
Off
ATC 1
When active trace control function is inactive
Off
When active trace control function is active
On
ATC 2
When active trace control function is inactive
Off
When active trace control function is active
On
ATC 4
When active trace control function is inactive
Off
When active trace control function is active
On
BRAKE HOLD
When brake fluid pressure is hold
ACT
When brake fluid pressure is not hold
INACT
When brake fluid pressure is decreases
RELEA
ATC 3
When active trace control function is inactive
Off
When active trace control function is active
On
ATC 5
When active trace control function is inactive
Off
When active trace control function is active
On
ARC BRAKE
When active ride control (brake control) function is in-
active
Off
When active ride control (brake control) function is ac-
tive
On
FL TIRE DISP
When the front LH tire is not displayed on the informa-
tion display in the combination meter
DEF
When the front LH tire is displayed on the information
display in the combination meter
1
FR TIRE DISP
When the front RH tire is not displayed on the informa-
tion display in the combination meter
DEF
When the front RH tire is displayed on the information
display in the combination meter
1
RL TIRE DISP
When the rear LH tire is not displayed on the informa-
tion display in the combination meter
DEF
When the rear LH tire is displayed on the information
display in the combination meter
1
RR TIRE DISP
When the rear RH tire is not displayed on the informa-
tion display in the combination meter
DEF
When the rear RH tire is displayed on the information
display in the combination meter
1
VEHICLE DISP
When the active ride control (brake control) function is
not displayed on the information display in the combi-
nation meter
DEF
When the active ride control (brake control) function is
displayed on the information display in the combina-
tion meter
1
Monitor item
Condition
Reference value in normal operation
DAS-200
< ECU DIAGNOSIS INFORMATION >
[CHASSIS CONTROL]
CHASSIS CONTROL MODULE
INTERRUPT DISP
When not interrupt displayed on the information dis-
play in the combination meter
NO REQ
When the hill start assist function is not interrupt dis-
played on the information display in the combination
meter
HOLD 1
When the hill start assist function is not interrupt dis-
played on the information display in the combination
meter
HOLD 2
When the advanced hill descent control function is not
interrupt displayed on the information display in the
combination meter
HDC
TURN DISP
When the straight-ahead status is displayed on the in-
formation display in the combination meter
N STEER
When the left turning status is displayed on the infor-
mation display in the combination meter
LEFT
When the right turning status is displayed on the infor-
mation display in the combination meter
RIGHT
ALC LEVEL
Displayed but not used
—
ALC STATUS
Displayed but not used
—
BRAKE HOLD DISP
When the operation condition is satisfied (inactive)
status of hill start assist function is displayed on the in-
formation display in the combination meter
ACT
When the operation condition is not satisfied status of
hill start assist function is displayed on the information
display in the combination meter
INACT
When the activation status of hill start assist function
is displayed on the information display in the combina-
tion meter
RELEA
ATC DISP
When the activation of active trace control function is
not displayed on the information display in the combi-
nation meter
Off
When the activation of active trace control function is
displayed on the information display in the combina-
tion meter
On
ARC BRAKE DISP
When the activation of active ride control (brake con-
trol) function is displayed on the information display in
the combination meter
On
When the activation of active ride control (brake con-
trol) function is not displayed on the information dis-
play in the combination meter
Off
HDC DISP
When the activation of advanced hill descent control
function is displayed on the information display in the
combination meter
On
When the activation of advanced hill descent control
function is not displayed on the information display in
the combination meter
Off
AEB CVT PERMIT
When transaxle control is authorized
On
When transaxle control is not authorized
Off
AEB STATUS
When active engine brake function is ON
On
When active engine brake function is OFF
Off
AEB COMMAND 1
When active engine brake function is inactive
0 – 0.1023 G
When active engine brake function is active
0 G
AEB COMMAND 2
Displayed but not used
—
Monitor item
Condition
Reference value in normal operation
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст