Nissan X-Trail 32. Instruction — part 1489
CENTER CONSOLE ASSEMBLY
IP-51
< REMOVAL AND INSTALLATION >
[RHD MODELS]
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
CENTER CONSOLE ASSEMBLY
Exploded View
INFOID:0000000010981697
Instrument lower cover RH
Instrument lower cover LH
Center console assembly
Console bracket (M/T models)
Rear ventilator duct 2 (if equipped)
Rear ventilator grille (if equipped)
Console rear finisher
Console mask
Console lid
Power socket (if equipped)
Hill descent control switch
(if equipped)
Heated seat switch LH
(if equipped)
Heated seat switch RH
(if equipped)
Console switch panel
Console switch panel
Console switch panel
4WD mode switch
(if equipped)
Ashtray
Parking brake switch
Console boot assembly
(M/T models)
A/T console finisher
(CVT models)
: Clip
: Pawl
: Metal clip
: N·m (kg-m, in-lb)
JMJIB0237GB
IP-52
< REMOVAL AND INSTALLATION >
[RHD MODELS]
CENTER CONSOLE ASSEMBLY
Removal and Installation
INFOID:0000000010981698
WARNING:
Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait for 3 minutes
or more.
REMOVAL
CAUTION:
When removing, always use a remover tool that is made of plastic.
1.
Put selector lever in
“
N
”
position (CVT models).
2.
Remove selector lever knob. Refer to
TM-403, "Removal and Installation"
. (CVT models)
3.
Remove shift lever knob. Refer to
TM-28, "Removal and Installation"
. (M/T models)
4.
Disengage fixing clip and pawls, and then remove instrument lower cover LH and RH according to numer-
ical order 1
→
2 indicated by arrows as shown in the figure.
5.
Remove A/T console finisher. (CVT models)
a.
Apply protective tape (A) on the part to protect it from damage.
b.
Disengage fixing metal clips and pawls using a remover tool (A),
and then remove A/T console finisher according to numerical
order 1
→
3 indicated by arrows as shown in the figure.
c.
Disconnect harness connector.
d.
Remove the following part after removing A/T console finisher.
Parking brake switch: Refer to
PB-156, "Removal and Installation"
6.
Remove console boot assembly. (M/T models)
: Clip
: Pawl
JMJIA9741ZZ
JMJIA9740ZZ
: Pawl
: Metal clip
JMJIA9775ZZ
CENTER CONSOLE ASSEMBLY
IP-53
< REMOVAL AND INSTALLATION >
[RHD MODELS]
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
a.
Disengage fixing metal clips and pawls, and then remove con-
sole boot assembly.
b.
Disconnect harness connector.
c.
Remove the following part after removing console boot assembly.
Parking brake switch: Refer to
PB-156, "Removal and Installation"
7.
Remove console switch panel.
a.
Apply protective tape (A) on the part to protect it from damage.
b.
Disengage fixing metal clips using a remover tool (A), and then
remove console switch panel from center console assembly.
c.
Disconnect harness connectors.
8.
Remove console mask.
a.
Open the console lid.
b.
Disengage fixing pawls, and then remove console mask by
arrow as shown in the figure.
9.
Remove console rear finisher assembly.
: Pawl
: Metal clip
JMJIB0184ZZ
JMJIA9816ZZ
: Metal clip
JMJIA9818ZZ
: Pawl
JMJIA9815ZZ
IP-54
< REMOVAL AND INSTALLATION >
[RHD MODELS]
CENTER CONSOLE ASSEMBLY
a.
Remove console rear finisher assembly fixing screw
.
b.
Disengage fixing metal clips, and then remove console rear fin-
isher assembly by arrows as shown in the figure.
c.
Remove the following part after removing console rear finisher assembly. (if equipped)
Rear ventilator grille: Refer to
VTL-14, "REAR VENTILATOR GRILLE : Removal and Installation"
.
10. Remove center console assembly fixing screws
.
• Front side
• Rear side
JMJIA9628ZZ
: Metal clip
JMJIA9757ZZ
JMJIA9747ZZ
JMJIA9748ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст