Nissan X-Trail 32. Instruction — part 286
CL-12
< PERIODIC MAINTENANCE >
CLUTCH FLUID
3.
Slide bleeding connector
in the direction of the arrow as
shown in the figure.
4.
Depress clutch pedal to gradually discharge clutch fluid.
CAUTION:
Since the inside of clutch tube is under hydraulic pressure,
hold the tube to prevent it from getting disconnected.
Refilling
INFOID:0000000010745323
CAUTION:
Keep painted surface on the body or other parts free of clutch fluid. If it spills, wipe up immediately
and wash the affected area with water.
1.
Check that there is no foreign material in reservoir tank, and then fill with new clutch fluid.
CAUTION:
Never reuse drained clutch fluid.
2.
Connect a transparent vinyl hose
to air bleeder of bleeding
connector .
3.
Press the lock pin
into the bleeding connector
, and main-
tain the position.
4.
Slide bleeding connector
in the direction of the arrow as
shown in the figure.
5.
Slowly depress clutch pedal to the full stroke position, and then
release the pedal.
CAUTION:
Since the inside of clutch tube is under hydraulic pressure,
hold the tube to prevent it from getting disconnected.
6.
Repeat step 5 at intervals of 2 or 3 seconds until new clutch fluid is discharged.
CAUTION:
Monitor clutch fluid level in reservoir tank so as not to empty the tank.
: Clutch housing
Dimension (A)
: 10 mm (0.39 in)
JPDIB0042ZZ
JSDIA5568ZZ
JPDIB0041ZZ
: Clutch housing
Dimension (A)
: 10 mm (0.39 in)
JPDIB0042ZZ
CLUTCH FLUID
CL-13
< PERIODIC MAINTENANCE >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
7.
Return clutch tube and lock pin in their original positions while clutch pedal is depressed.
8.
Perform the air bleeding. Refer to
Air Bleeding
INFOID:0000000010745324
CAUTION:
• Monitor clutch fluid level in reservoir tank so as not to empty the tank.
• Keep painted surface on the body or other parts free of clutch fluid. If it spills, wipe up immediately
and wash the affected area with water.
NOTE:
Do not use a vacuum assist or any other type of power bleeder on this system. Use of a vacuum assist or
power bleeder will not purge all the air from the system.
1.
Fill reservoir tank with new clutch fluid.
CAUTION:
Never reuse drained clutch fluid.
2.
Connect a transparent vinyl hose
to air bleeder of bleeding
connector .
3.
“Depress” and “Release” the clutch pedal slowly and fully 15
times at an interval of 2 to 3 seconds and release the clutch
pedal.
4.
Press the lock pin
into the bleeding connector
, and main-
tain the position.
CAUTION:
Since the inside of clutch tube is under hydraulic pressure,
hold the tube to prevent it from getting disconnected.
5.
Slide bleeding connector
in the direction of the arrow as
shown in the figure.
6.
Depress the clutch pedal soon and hold it, and then bleed the air
from the piping.
CAUTION:
Since the inside of clutch tube is under hydraulic pressure,
hold the tube to prevent it from getting disconnected.
7.
Return clutch tube and lock pin in their original positions.
8.
Release clutch pedal and wait for 5 seconds.
9.
Repeat steps 3 to 8 until no bubbles are observed in the clutch fluid.
10. Check that the fluid level in the reservoir tank is within the specified range after air bleeding. Refer to
JSDIA5568ZZ
JPDIB0041ZZ
: Clutch housing
Dimension (A)
: 10 mm (0.39 in)
JPDIB0042ZZ
CL-14
< REMOVAL AND INSTALLATION >
CLUTCH PEDAL
REMOVAL AND INSTALLATION
CLUTCH PEDAL
LHD
LHD : Exploded View
INFOID:0000000010745325
LHD : Removal and Installation
INFOID:0000000010745326
REMOVAL
1.
Remove instrument lower panel LH. Refer to
IP-14, "Removal and Installation"
.
2.
Disconnect clutch pedal position switch harness connector.
3.
Disconnect clutch interlock switch harness connector.
4.
Disconnect clutch pedal stroke sensor harness connector.
5.
Disconnect harness clip from clutch pedal bracket
.
Clutch interlock switch
Clutch pedal stroke sensor
Clutch pedal position switch
Clip
Clutch pedal assembly
: N·m (kg-m, ft-lb)
JSDIA6100GB
: Hole for harness clip
JSDIA6104ZZ
CLUTCH PEDAL
CL-15
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
6.
Remove clutch pedal stroke sensor
.
a.
Pull sensor lever cover
b.
While turn lever pin
and pull it.
c.
Remove clutch pedal stroke sensor.
7.
Remove master cylinder rod end from clutch pedal lever
.
8.
Remove clutch pedal position switch
and clip
from clutch
pedal bracket.
9.
Remove clutch interlock switch
and clip
from clutch pedal
bracket.
10. Remove clutch pedal assembly.
11. Perform inspection after removal. Refer to
JSDIA5591ZZ
JSDIA6109ZZ
JSDIA6105ZZ
JSDIA6106ZZ
JSDIA5589ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст