Nissan X-Trail 32. Instruction — part 287
CL-16
< REMOVAL AND INSTALLATION >
CLUTCH PEDAL
INSTALLATION
Note the following, and install in the reverse order of removal.
• Push clip until it clicks.
• Press master cylinder rod end to pin of clutch pedal until it stops.
• Perform inspection and adjustment after installation. Refer to
CL-16, "LHD : Inspection and Adjustment"
• Install clutch pedal stroke sensor, according to the following procedure.
CAUTION:
Install clutch pedal position switch before installing clutch pedal stroke sensor.
1.
Insert pawl
into the hole and hook it, and fit lever pin
into
the hole. And then clutch pedal stroke sensor
is installed tem-
porary.
2.
Push lever pin
and insert it into the hole deeply.
3.
Turn lever pin
as shown in the figure and fix lever pin to stop-
per
. And then clutch pedal stroke sensor
is installed com-
pletely.
4.
Push sensor lever cover
, then hold on pin
of clutch pedal.
LHD : Inspection and Adjustment
INFOID:0000000010745327
INSPECTION AFTER REMOVAL
JSDIA5601ZZ
JSDIA5602ZZ
JSDIA5603ZZ
JSDIA5604ZZ
CLUTCH PEDAL
CL-17
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
• Check clutch pedal for bend, damage, or a cracked weld. If bend, damage, or a cracked weld is found,
replace clutch pedal assembly.
• Check pedal stopper rubber
. If damage or deformation is found,
replace clutch pedal assembly.
• Check pedal pad
. If wear or damage is found, replace clutch
pedal assembly.
INSPECTION AFTER INSTALLATION
• Check the clutch pedal height, clutch pedal height at clutch disengagement, and clutch pedal play. Refer to
CL-9, "Inspection and Adjustment"
• Check the clutch pedal position switch position. Refer to
CL-9, "Inspection and Adjustment"
• Check the clutch interlock switch position. Refer to
CL-9, "Inspection and Adjustment"
.
ADJUSTMENT AFTER INSTALLATION
• Adjust the clutch pedal position switch position. Refer to
CL-9, "Inspection and Adjustment"
• Adjust the clutch interlock switch position. Refer to
CL-9, "Inspection and Adjustment"
.
• Perform reset of clutch pedal stroke sensor, after installation clutch pedal or clutch pedal stroke sensor.
RHD
JSDIA6112ZZ
JSDIA6113ZZ
CL-18
< REMOVAL AND INSTALLATION >
CLUTCH PEDAL
RHD : Exploded View
INFOID:0000000010745328
RHD : Removal and Installation
INFOID:0000000010745329
REMOVAL
1.
Remove instrument lower panel RH. Refer to
IP-41, "Removal and Installation"
2.
Disconnect clutch pedal position switch harness connector.
3.
Disconnect clutch interlock switch harness connector.
4.
Disconnect clutch pedal stroke sensor harness connector.
5.
Disconnect harness clip from clutch pedal bracket
.
Clutch pedal assembly
Clutch pedal stroke sensor
Clutch pedal position switch
Clip
Pedal pad
Clutch interlock switch
: N·m (kg-m, ft-lb)
JSDIA5585GB
: Hole for harness clip
JSDIA6110ZZ
CLUTCH PEDAL
CL-19
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
6.
Remove clutch pedal stroke sensor
.
a.
Pull sensor lever cover
b.
While turn lever pin
and pull it.
c.
Remove clutch pedal stroke sensor.
7.
Remove master cylinder rod end from clutch pedal lever
.
8.
Remove clutch pedal position switch
and clip
from clutch
pedal bracket.
9.
Remove clutch interlock switch
and clip
from clutch pedal
bracket.
10. Remove clutch pedal assembly.
11. Remove pedal pad from clutch pedal.
12. Perform inspection after removal. Refer to
JSDIA5591ZZ
JSDIA6109ZZ
JSDIA5592ZZ
JSDIA5593ZZ
JSDIA5594ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст