Nissan X-Trail 32. Instruction — part 160
BRC-106
< BASIC INSPECTION >
[WITH VDC (ESP)]
CONFIGURATION [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)]
>> End of work.
C10D7 PARKING BRAKE SYSTEM
BRC-107
< DTC/CIRCUIT DIAGNOSIS >
[WITH VDC (ESP)]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
DTC/CIRCUIT DIAGNOSIS
C10D7 PARKING BRAKE SYSTEM
DTC Description
INFOID:0000000010723661
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connector
• Electric parking brake control module
• ABS actuator and electric unit (control unit)
FAIL-SAFE
The following functions are suspended.
• Deceleration control (brake control by VDC function) performed by pulling the parking brake switch while
driving the vehicle [10 km/h (6.2 MPH) or more].
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
2.
Perform self-diagnosis for “ABS”.
Is DTC “C10D7” detected?
YES
>> Proceed to
BRC-107, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010723662
1.
CHECK ELECTRIC PARKING BRAKE SYSTEM
With CONSULT
Perform self-diagnosis for “EHS/PKB”.
Is any DTC detected?
YES
>> Check the DTC. Refer to
NO
>> GO TO 2.
2.
CHECK CONNECTOR AND TERMINALS
1.
Turn the ignition switch OFF.
2.
Disconnect the electric parking brake control module harness connector.
3.
Disconnect the ABS actuator and electric unit (control unit) harness connector.
4.
Check the each harness connector for disconnection or looseness.
5.
Check the each pin terminals for damage or loose connection with harness.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair or replace error-detected parts, securely lock the connector, and GO TO 3.
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C10D7
PARKING BRAKE SYSTEM
(Parking brake system)
When a malfunction is detected in electric parking brake system.
BRC-108
< DTC/CIRCUIT DIAGNOSIS >
[WITH VDC (ESP)]
C10D7 PARKING BRAKE SYSTEM
3.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Connect the electric parking brake control module harness connector.
2.
Connect the ABS actuator and electric unit (control unit) harness connector.
3.
Erase self-diagnosis result for “ABS”.
4.
Turn the ignition switch OFF to ON.
5.
Perform self-diagnosis for “ABS”.
Is any DTC “C10D7” or “U1000” detected?
YES (“C10D7”)>>Replace the ABS actuator and electric unit (control unit).
• LHD models: Refer to
BRC-217, "LHD : Removal and Installation"
• RHD models: Refer to
BRC-220, "RHD : Removal and Installation"
.
LAN-17, "Trouble Diagnosis Flow Chart"
NO
>> INSPECTION END
C1101, C1102, C1103, C1104 WHEEL SENSOR
BRC-109
< DTC/CIRCUIT DIAGNOSIS >
[WITH VDC (ESP)]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
C1101, C1102, C1103, C1104 WHEEL SENSOR
DTC Description
INFOID:0000000010723663
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connector
• Wheel sensor
• ABS actuator and electric unit (control unit)
FAIL-SAFE
The following functions are suspended.
• VDC function
• TCS function
• ABS function
• EBD function (only when both 2 rear wheels are malfunctioning)
• Brake limited slip differential (BLSD) function
• Brake assist function
• hill start assist function
• Brake force distribution function
• Advanced hill descent control function (4WD models with gasoline engine)
• Active trace control function (control of chassis control module)
• Active ride control function (control of chassis control module)
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Start the engine.
2.
Drive the vehicle at approx. 30 km/h (19 MPH) or more for approx. 1 minute.
3.
Stop the vehicle.
4.
Perform self-diagnosis for “ABS”.
Is any DTC “C1101”, “C1102”, “C1103”, “C1104” detected?
YES
>> Proceed to
BRC-109, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010723664
CAUTION:
Never check between wheel sensor harness connector terminals.
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1101
RR RH SENSOR-1
(Rear RH wheel sensor-1)
When an open circuit is detected in rear RH wheel sensor circuit.
C1102
RR LH SENSOR-1
(Rear LH wheel sensor-1)
When an open circuit is detected in rear LH wheel sensor circuit.
C1103
FR RH SENSOR-1
(Front RH wheel sensor-1)
When an open circuit is detected in front RH wheel sensor circuit.
C1104
FR LH SENSOR-1
(Front LH wheel sensor-1)
When an open circuit is detected in front LH wheel sensor circuit.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст