Nissan X-Trail 32. Instruction — part 1589
MWI-38
< SYSTEM DESCRIPTION >
SYSTEM
• The ignition switch is in a position other than ON.
TIMING CHART
WARNING LAMPS/INDICATOR LAMPS : Front Fog Lamp Indicator Lamp
INFOID:0000000010782906
DESIGN/PURPOSE
Front fog lamp indicator lamp informs the driver that front fog lamp is
in ON status.
BULB CHECK
Not applicable
SYNCHRONIZATION WITH MASTER WARNING LAMP
Not applicable
OPERATION AT COMBINATION METER CAN COMMUNICATION CUT-OFF OR UNUSUAL SIG-
NAL
For actions on CAN communications blackout in the combination meter, refer to
JSOIA0862GB
JPNIA1878ZZ
MWI
SYSTEM
MWI-39
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
SYSTEM DIAGRAM
SIGNAL PATH
• BCM transmits front fog light request signal to combination meter via CAN communication when front fog
lamp is in ON status.
• When combination meter receives front fog light request signal, combination meter turns front fog lamp indi-
cator lamp ON.
LIGHTING CONDITION
When front fog lamp is turned ON.
SHUTOFF CONDITION
When front fog lamp is turned OFF.
WARNING LAMPS/INDICATOR LAMPS : Glow Indicator Lamp
INFOID:0000000010781001
DESIGN/PURPOSE
The glow indicator lamp turns ON in quick preheat mode and informs
the driver that the glow plug is under preheating condition.
BULB CHECK
Not applicable
SYNCHRONIZATION WITH MASTER WARNING LAMP
Not applicable
OPERATION AT COMBINATION METER CAN COMMUNICATION CUT-OFF OR UNUSUAL SIG-
NAL
For the operation for CAN communications blackout or abnormal signal reception, refer to
JMLIA4102GB
JPNIA1884ZZ
MWI-40
< SYSTEM DESCRIPTION >
SYSTEM
SYSTEM DIAGRAM
SIGNAL PATH
• ECM performs the glow control, according to an IGN ON signal, water temperature signal, and engine speed
signal. ECM transmits a glow indicator lamp signal to the combination meter in quick preheat mode via CAN
communication .
• The combination meter turns ON the glow indicator lamp, according to a glow indicator lamp signal received
from ECM via CAN communication.
LIGHTING CONDITION
When any of the following conditions is satisfied:
• Ignition switch: ON
• Mode: Quick preheat mode
NOTE:
The glow indicator lamp does not turn ON in after glow mode.
SHUTOFF CONDITION
When any of the following conditions is satisfied:
• Ignition switch: OFF
• Quick preheat mode is complete.
• Engine start
TIMING CHART
WARNING LAMPS/INDICATOR LAMPS : High Beam Assist Indicator Lamp
INFOID:0000000010782916
DESIGN/PURPOSE
JPBIA6027GB
JPBIA6028GB
MWI
SYSTEM
MWI-41
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
High beam assist indicator lamp informs the driver that the high
beam assist system is in operating status.
BULB CHECK
Not applicable
SYNCHRONIZATION WITH MASTER WARNING LAMP
Not applicable
OPERATION AT COMBINATION METER CAN COMMUNICATION CUT-OFF OR UNUSUAL SIG-
NAL
For actions on CAN communications blackout in the combination meter, refer to
SYSTEM DIAGRAM
SIGNAL PATH
• BCM transmits the high beam assist indicator lamp signal to the combination meter via CAN communication
when the high beam assist system operation permission conditions are satisfied.
• When combination meter receives high beam assist indicator lamp signal, combination meter turns high
beam assist indicator lamp ON.
LIGHTING CONDITION
High beam assist system operation permission conditions are satisfied.
{[Lighting switch HI with the lighting switch AUTO and ignition switch ON [Only when the illuminating judgment
by auto light function is ON. For details, refer to
EXL-24, "AUTO LIGHT SYSTEM : System Description"
(LED
headlamp) or
EXL-228, "AUTO LIGHT SYSTEM : System Description"
(halogen headlamp).]}
SHUTOFF CONDITION
High beam assist system operation permission conditions are not satisfied.
WARNING LAMPS/INDICATOR LAMPS : High Beam Indicator Lamp
INFOID:0000000010782907
DESIGN/PURPOSE
JMLIA4103ZZ
JMLIA4104GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст