Nissan X-Trail 32. Instruction — part 810
P2119 ELECTRIC THROTTLE CONTROL ACTUATOR
EC-369
< DTC/CIRCUIT DIAGNOSIS >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P2119 ELECTRIC THROTTLE CONTROL ACTUATOR
DTC Description
INFOID:0000000010775264
DTC DETECTION LOGIC
POSSIBLE CAUSE
Electric throttle control actuator
FAIL-SAFE
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A AND B
1.
Turn ignition switch ON and wait at least 1 second.
2.
Set selector lever to D position and wait at least 3 seconds.
3.
Set selector lever to P position.
4.
Turn ignition switch OFF and wait at least 10 seconds.
5.
Turn ignition switch ON and wait at least 1 second.
6.
Set selector lever to D position and wait at least 3 seconds.
7.
Set selector lever to P position.
8.
Turn ignition switch OFF, wait at least 10 seconds and then turn ON.
9.
Check DTC.
Is DTC detected?
YES
>> Proceed to
.
NO
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION C
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P2119
ETC ACTR-B1
(Throttle actuator control throttle
body range/performance)
A
Electric throttle control actuator does not function properly due to the return
spring malfunction.
B
Throttle valve opening angle in fail-safe mode is not in specified range.
C
ECM detects the throttle valve is stuck open.
Engine operating condition in fail-safe mode
Fail safe mode
Vehicle behavior
Traveling con-
trol mode
Accelerator an-
gle variation
control
ECM controls the accelerator pedal depression speed to make it slower than actual speed. This
causes a drop in accelerating performance and encourages the driver to repair malfunction.
NOTE:
ECM does not control the accelerator pedal releasing speed.
Engine output
control
ECM reduces the engine output, according to the rise in engine speed. This reduces the vehicle
speed to encourage the driver to repair malfunction.
Others
ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed
opening (approx. 5 degrees) by the return spring.
NOTE:
For pattern A and B refer to A and B of P2119 DTC detection logic.
For C of P2119 DTC detection logic ECM behaves as above.
EC-370
< DTC/CIRCUIT DIAGNOSIS >
[MR20DD]
P2119 ELECTRIC THROTTLE CONTROL ACTUATOR
1.
Turn ignition switch ON and wait at least 1 second.
2.
Set selector lever to D position and wait at least 3 seconds.
3.
Set selector lever to P position.
4.
Start engine and let it idle for 3 seconds.
5.
Check DTC.
Is DTC detected?
YES
>> Proceed to
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010775265
1.
CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY
1.
Turn ignition switch OFF.
2.
Remove the intake air duct. Refer to
EM-31, "Removal and Installation"
.
3.
Check if foreign matter is caught between the throttle valve and the housing.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Remove the foreign matter and clean the electric throttle control actuator inside, then perform
throttle valve closed position learning. Refer to
2.
REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
Replace electric throttle control actuator. Refer to
EM-33, "Removal and Installation"
>> INSPECTION END
P2122, P2123 APP SENSOR
EC-371
< DTC/CIRCUIT DIAGNOSIS >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P2122, P2123 APP SENSOR
DTC Description
INFOID:0000000010775266
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connectors (APP sensor 1 circuit is open or shorted.)
• Accelerator pedal position sensor (APP sensor 1)
FAIL-SAFE
DTC CONFIRMATION PROCEDURE
1.
CHECK DTC PRIORITY
If DTC P2122 or P2123 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.
Is applicable DTC detected?
YES
>> Perform diagnosis of applicable. Refer to
.
NO
>> GO TO 2.
2.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start engine and let it idle for 1 second.
2.
Check DTC.
Is DTC detected?
YES
>> Proceed to
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P2122
APP SEN 1/CIRC
(Throttle/pedal position sensor/switch “D”
circuit low)
An excessively low voltage from the APP sensor 1 is sent to ECM.
P2123
APP SEN 1/CIRC
(Throttle/pedal position sensor/switch “D”
circuit high)
An excessively high voltage from the APP sensor 1 is sent to ECM.
Engine operating condition in fail-safe mode
Fail safe mode
Vehicle behavior
Others
The ECM controls the electric throttle control actuator in regulating the throttle opening in order
for the idle position to be within +10 degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal condition.
Therefore, the acceleration will be poor.
NOTE:
If accelerator pedal position sensor 1 and 2 malfunction at the same time conducts following con-
trol.
• ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed
opening (approx. 5 degrees) by the return spring.
EC-372
< DTC/CIRCUIT DIAGNOSIS >
[MR20DD]
P2122, P2123 APP SENSOR
Diagnosis Procedure
INFOID:0000000010775267
1.
CHECK DTC PRIORITY
If DTC P2122 or P2123 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.
Is applicable DTC detected?
YES
>> Perform diagnosis of applicable. Refer to
NO
>> GO TO 2.
2.
CHECK APP SENSOR 1 POWER SUPPLY CIRCUIT-1
1.
Turn ignition switch OFF.
2.
Disconnect accelerator pedal position (APP) sensor harness connector.
3.
Turn ignition switch ON.
4.
Check the voltage between APP sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 3.
3.
CHECK APP SENSOR 1 POWER SUPPLY CIRCUIT-2
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between APP sensor harness connector and ECM harness connector.
4.
Also check harness for short to ground and to power.
Is the inspection result normal?
YES
>> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace malfunctioning part.
4.
CHECK APP SENSOR 1 GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between APP sensor harness connector and ECM harness connector.
4.
Also check harness for short to ground and to power.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace malfunctioning part.
+
−
Voltage
(Approx.)
APP sensor
Connector
Terminal
CVT models
E110
4
Ground
5 V
M/T models
E167
+
−
Continuity
APP sensor
ECM
Connector
Terminal
Connector
Terminal
CVT models
E110
4
E16
122
Existed
M/T models
E167
+
−
Continuity
APP sensor
ECM
Connector
Terminal
Connector
Terminal
CVT models
E110
2
E16
127
Existed
M/T models
E167
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст