Nissan Teana J32. Instruction — part 1160
TM-164
< ON-VEHICLE REPAIR >
[CVT: RE0F09B]
AIR BREATHER HOSE
AIR BREATHER HOSE
Exploded View
INFOID:0000000003849103
Removal and Installation
INFOID:0000000003849104
REMOVAL
1.
Remove air duct (inlet) and air cleaner case. Refer to
.
2.
Remove air breather hose from transaxle assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Check that air breather hose is not collapsed or blocked due to folding or bending when installed.
• Install air breather hose to air breather tube so that the paint mark
(A) faces upward. Also insert hose to the bend of air breather tube.
1.
Air cleaner case
2.
Air breather hose
3.
Transaxle assembly
4.
Heater pipe
: Vehicle front
JPDIA0592ZZ
SCIA7584J
FLUID COOLER SYSTEM
TM-165
< ON-VEHICLE REPAIR >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
FLUID COOLER SYSTEM
Exploded View
INFOID:0000000003849105
Removal and Installation
INFOID:0000000003849106
REMOVAL
1.
Remove front under cover.
2.
Remove fender protector (left side).
3.
Remove air duct (inlet). Refer to
4.
Remove fluid cooler hose A and fluid cooler hose B.
5.
Remove fluid cooler tube.
INSTALLATION
Note the following, and install in the reverse order of removal.
When installing CVT fluid cooler tube (1) to transaxle assembly:
• Contact CVT fluid cooler tube to a boss portion (A) of the transaxle
case.
• Tighten the bolt of CVT fluid cooler tube without moving the CVT
fluid cooler tube.
1.
Copper washer
2.
Fluid cooler tube
3.
Hose clamp
4.
Fluid cooler hose A
5.
Fluid cooler hose B
6.
Transaxle assembly
A.
To radiator assembly
Refer to
JPDIA0792GB
JPDIA0628ZZ
TM-166
< ON-VEHICLE REPAIR >
[CVT: RE0F09B]
FLUID COOLER SYSTEM
*: Refer to the illustrations for the specific position of each hose clamp tab.
• The illustrations indicate the view from the hose ends.
• When installing hose clamps the center line of each clamp tab
should be positioned as shown in the figure.
• Insert CVT water hose according to dimension ( ) described
below.
• Set hose clamps (1) at the both ends of fluid cooler hose (2) with
dimension (A) from the hose edge.
• Hose clamp should not interfere with the bulge.
CVT water hose
Hose end
Paint mark
Position of hose clamp*
Fluid cooler hose A
Radiator assembly
Facing upward
A
Fluid cooler tube
Facing upward
C
Fluid cooler hose B
Radiator assembly
Facing backward
B
Transaxle assembly
Facing upward
C
D: Vehicle front
E: Vehicle upper
JPDIA0869ZZ
(1)
(2)
Tube type
Dimension
Fluid cooler hose
A
Radiator assembly
A
30 mm (1.18 in) (Insert the
hose until the hose touches
the radiator)
Fluid cooler tube
B
End reaches the tube bend
R position.
Fluid cooler hose
B
Radiator assembly
Transaxle assem-
bly
JPDIA0863ZZ
Dimension (A)
: 5 – 9 mm (0.20 – 0.35 in)
SCIA8123E
FLUID COOLER SYSTEM
TM-167
< ON-VEHICLE REPAIR >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Inspection
INFOID:0000000003849107
After completing installation, check for engine coolant leakage and check engine coolant level. Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст