Nissan Teana J32. Instruction — part 1200
TM-324
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
SECONDARY SPEED SENSOR
SECONDARY SPEED SENSOR
Exploded View
INFOID:0000000003806533
Removal and Installation
INFOID:0000000003806534
REMOVAL
1.
Disconnect the battery cable from the negative terminal.
2.
Remove air duct (inlet) and air cleaner case. Refer to
.
3.
Disconnect secondary speed sensor connector.
4.
Remove secondary speed sensor and shim.
5.
Remove O-ring from secondary speed sensor.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Never reuse O-ring.
• Apply CVT fluid to O-ring.
Inspection
INFOID:0000000003806535
After completing installation, check for CVT fluid leakage and check CVT fluid level. Refer to
.
1.
Secondary speed sensor
2.
O-ring
3.
Transaxle assembly
4.
Shim
: Apply CVT Fluid NS-2.
Refer to
for symbols not described above.
JPDIA0771GB
DIFFERENTIAL SIDE OIL SEAL
TM-325
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
DIFFERENTIAL SIDE OIL SEAL
Exploded View
INFOID:0000000003806536
Removal and Installation
INFOID:0000000003806537
REMOVAL
1.
Remove drive shaft assembly. Refer to
.
2.
Remove differential side oil seals (1) using a flat-bladed screw-
driver (A).
CAUTION:
Be careful not to scratch transaxle case and converter
housing.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Drive each differential side oil seal evenly using a commercial ser-
vice tool so that differential side oil seal protrudes by the dimension
(A) or (B) respectively.
Unit: mm (in)
NOTE:
Differential side oil seal pulling direction is used as the reference.
CAUTION:
• Never reuse differential side oil seals.
• Apply CVT fluid to differential side oil seals.
1.
RH differential side oil seal
2.
LH differential side oil seal
3.
Transaxle assembly
: Apply CVT Fluid NS-2.
Refer to
for symbols not described above.
JPDIA0767ZZ
JPDIA0118ZZ
Dimension A (transaxle case side)
1.8
±
0.5 (0.071
±
0.020)
Dimension B (converter housing side)
2.2
±
0.5 (0.087
±
0.020)
SCIA6608J
TM-326
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
DIFFERENTIAL SIDE OIL SEAL
Drift to be used:
Inspection
INFOID:0000000003806538
After completing installation, check for CVT fluid leakage and check CVT fluid level. Refer to
.
Location
Tool number
Transaxle case side
Commercial service tool [Outer diameter: 54 mm (2.13 in), inner di-
ameter: 47 mm (1.85 in)]
Converter housing side
OIL PUMP FITTING BOLT
TM-327
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OIL PUMP FITTING BOLT
Description
INFOID:0000000003806542
Replace the oil pump fitting bolt and the O-ring if oil leakage or exudes from the oil pump fitting bolt.
Exploded View
INFOID:0000000003806543
Removal and Installation
INFOID:0000000003806544
REMOVAL
1.
Remove Oil pump fitting bolt (1) from transaxle assembly.
2.
Remove O-ring from oil pump fitting bolt.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Never reuse oil pump fitting bolt and O-ring.
• Apply CVT fluid to O-ring.
Inspection
INFOID:0000000003806545
After completing installation, check for CVT fluid leakage and check CVT fluid level. Refer to
.
1.
Oil pump fitting bolt
2.
O-ring
3.
Transaxle assembly
: Apply CVT Fluid NS-2.
Refer to
for symbols not described above.
JPDIA0763GB
JPDIA0077ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст