Nissan Teana J32. Instruction — part 1201
TM-328
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
AIR BREATHER HOSE
AIR BREATHER HOSE
Exploded View
INFOID:0000000003806546
Removal and Installation
INFOID:0000000003806547
REMOVAL
1.
Remove air duct (inlet) and air cleaner case. Refer to
.
1.
Remove clip from the bracket.
2.
Remove air breather hose from transaxle assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Install air breather hose with paint mark facing upward.
• Insert air breather hose a minimum of 17 mm (0.67 in) onto air breather tube (to end of air breather
tubes radius end).
• Install air breather hose to bracket by fully inserting the clip.
• Make sure there are no pinched or restricted areas on air breather hose caused by bending or wind-
ing when installing it.
1.
Air breather hose
2.
Clip
3.
Bracket
4.
Transaxle assembly
A.
Air breather tube
B.
Paint mark
: Vehicle front
JPDIA0768ZZ
FLUID COOLER SYSTEM
TM-329
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
FLUID COOLER SYSTEM
Exploded View
INFOID:0000000003886234
Removal and Installation
INFOID:0000000003886235
REMOVAL
1.
Remove air duct (inlet). Refer to
2.
Remove engine under cover. Refer to
.
3.
Remove fender protector (left side). Refer to
EXT-22, "FENDER PROTECTOR : Exploded View"
.
4.
Remove fluid cooler hose A and fluid cooler hose B.
5.
Remove CVT fluid cooler tube from transaxle assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Never reuse copper washer.
1.
Hose clamp
2.
Fluid cooler hose A
3.
Fluid cooler hose B
4.
Copper washer
5.
CVT fluid cooler tube
6.
CVT fluid cooler tube
7.
Transaxle assembly
A.
To radiator
: Vehicle front
Refer to
JPDIA0787GB
TM-330
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
FLUID COOLER SYSTEM
• When installing CVT fluid cooler tube (1) to transaxle assembly:
- Contact CVT fluid cooler tube a boss portion (A) of the transaxle
case.
- Tighten the bolt of CVT fluid cooler tube without moving the CVT
fluid cooler tube
• Refer to the followings when installing fluid cooler hose.
*: Refer to the illustrations for the specific position each hose clamp tab.
- The illustrations indicate the view from the hose ends.
- When installing hose clamps center line of each hose clamp tab
should be positioned as shown in the figure.
- Insert fluid cooler hose according to dimension (A) described below.
JPDIA0772ZZ
Fluid cooler hose
Hose end
Paint mark
Position of hose clamp
*
A
Radiator assembly side
Facing backward
A
CVT fluid cooler tube side
Facing upward
B
B
Radiator assembly side
Facing upward
C
CVT fluid cooler tube side
Facing upward
D
E
: Vehicle front
F
: Vehicle upper
JPDIA0801ZZ
(1)
(2)
Tube type
Dimension A
Fluid cooler hose A
Radiator side
A
End reaches the tube bend R position.
CVT fluid cooler tube side
B
33 mm (1.30 in) [End reaches the 2-stage bulge (D).]
Fluid cooler hose B
Radiator side
C
Insert the hose until the hose touches the radiator.
CVT fluid cooler tube side
B
33 mm (1.30 in) [End reaches the 2-stage bulge (D).]
JPDIA0860ZZ
FLUID COOLER SYSTEM
TM-331
< ON-VEHICLE REPAIR >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
- Set hose clamps (1) at the both ends of fluid cooler hose (2) with
dimension (A) from the hose edge.
- Hose clamp should not interfere with the bulge of fluid cooler tube.
Inspection
INFOID:0000000003886236
After completing installation, check for CVT fluid leakage and CVT fluid level. Refer to
.
Dimension A
: 5 – 9 mm (0.20 – 0.35 in)
SCIA8123E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст