Nissan Teana J32. Instruction — part 471
EM-8
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000003802234
Tool number
(SPX North America No.)
Tool name
Description
KV10116200
(J26336-A)
Valve spring compressor
1. KV10115900
(J26336-20)
Attachment
2.KV10109220
(
—
)
Adapter
Disassembling valve mechanism
Part (1) is a component of KV10116200
(J26336-A), but Part (2) is not so.
KV10107902
(J38959)
Valve oil seal puller
Replacing valve oil seal
KV10115600
(J-38958)
Valve oil seal drift
Installing valve oil seal
Use side A.
a: 20 mm (0.79 in) dia.
b: 13 mm (0.51 in) dia.
c: 10 mm (0.406 in)
d: 8 mm (0.31 in) dia.
e: 10.7 mm (0.421 in)
f: 5 mm (0.20 in) dia.
EM03470000
(J8037)
Piston ring compressor
Installing piston assembly into cylinder bore
ST16610001
(J23907)
Pilot bushing puller
Removing pilot converter
KV10111100
(J37228)
Seal cutter
Removing oil pan (lower and upper), front and
rear timing chain case, etc.
PBIC1650E
NT011
S-NT603
NT044
NT045
NT046
PREPARATION
EM-9
< PREPARATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Commercial Service Tool
INFOID:0000000003802235
KV10112100
(BT8653-A)
Angle wrench
Tightening bolts for connecting rod bearing
cap, cylinder head, etc. in angle
KV10117100
(J3647-A)
Heated oxygen sensor wrench
Loosening or tightening air fuel ratio sensor 1
For 22 mm (0.87 in) width hexagon nut
KV10114400
(J38365)
Heated oxygen sensor wrench
Loosening or tightening heated oxygen sen-
sor 2
a: 22 mm (0.87 in)
—
(J-45488)
Quick connector release
Removing fuel tube quick connectors in en-
gine room
(Available in SEC. 164 of PARTS CATALOG:
Part No. 16441 6N210)
Tool number
(SPX North America No.)
Tool name
Description
NT014
NT379
NT636
PBIC0198E
(SPX North America No.)
Tool name
Description
(
—
)
Power tool
Loosening bolts and nuts
(
—
)
Tube presser
Pressing the tube of liquid gasket
PBIC0190E
NT052
EM-10
< PREPARATION >
PREPARATION
(
—
)
Instruction lift table caddy
Removing and installing engine
(J24239-01)
Cylinder head bolt wrench
Loosening and tightening cylinder head bolt,
and used with the angle wrench [SST:
KV10112100 (BT8653-A)]
a: 13 mm (0.51 in) dia.
b: 12 mm (0.47 in)
c: 10 mm (0.39 in)
(
—
)
1.Compression tester
2.Adapter
Checking compression pressure
(
—
)
Spark plug wrench
Removing and installing spark plug
a: 14 mm (0.55 in)
(
—
)
Pulley holder
Removing and installing crankshaft pulley
(
—
)
Valve seat cutter set
Finishing valve seat dimensions
(
—
)
Piston ring expander
Removing and installing piston ring
(SPX North America No.)
Tool name
Description
ZZA1210D
NT583
ZZA0008D
JPBIA0399ZZ
ZZA1010D
NT048
NT030
PREPARATION
EM-11
< PREPARATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
(
—
)
Valve guide drift
Removing and installing valve guide
Intake and Exhaust:
a: 9.5 mm (0.374 in) dia.
b: 5.5 mm (0.217 in) dia.
(
—
)
Valve guide reamer
(1): Reaming valve guide inner hole
(2): Reaming hole for oversize valve guide
Intake and Exhaust:
d
1
: 6.0 mm (0.236 in) dia.
d
2
: 10.2 mm (0.402 in) dia.
a: (J-43897-18)
b: (J-43897-12)
Oxygen sensor thread cleaner
Reconditioning the exhaust system threads
before installing a new air fuel ratio sensor and
heated oxygen sensor (Use with anti-seize lu-
bricant shown below.)
a: J-43897-18 [18 mm (0.71 in) dia.] for zir-
conia heated oxygen sensor and air fuel
ratio sensor
b: J-43897-12 [12 mm (0.47 in) dia.] for tita-
nia heated oxygen sensor
(
—
)
Anti-seize lubricant (Permatex 133AR
or equivalent meeting MIL specifica-
tion MIL-A-907)
Lubricating air fuel ratio sensor and oxygen
sensor threads cleaning tool when recondi-
tioning exhaust system threads
(SPX North America No.)
Tool name
Description
NT015
NT016
AEM488
AEM489
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст