Nissan Teana J32. Instruction — part 14
RECLINING SWITCH
ADP-49
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
Is the inspection result normal?
YES
>> Replace driver seat control unit. Refer to
ADP-136, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK RECLINING SWITCH
ADP-49, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace power seat switch (driver side). Refer to
ADP-138, "Removal and Installation"
.
4.
CHECK INTERMITTENT INCIDENT
GI-35, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000003759126
1.
CHECK RECLINING SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect power seat switch (driver side) connector.
3.
Check continuity between power seat switch (driver side) terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace power seat switch (driver side). Refer to
ADP-138, "Removal and Installation"
.
Power seat switch (driver side)
Condition
Continuity
Terminal
36
13
Reclining switch (backward)
Operate
Existed
Release
Not existed
14
Reclining switch (forward)
Operate
Existed
Release
Not existed
ADP-50
< COMPONENT DIAGNOSIS >
LIFTING SWITCH (FRONT)
LIFTING SWITCH (FRONT)
Description
INFOID:0000000003759127
Lifting switch (front) is equipped to the power seat switch on the seat cushion side surface. The operation sig-
nal is inputted to the driver seat control unit when the lifting switch (front) is operated.
Component Function Check
INFOID:0000000003759128
1.
CHECK FUNCTION
1.
Select “LIFT FR SW-UP”, “LIFT FR SW-DN” in “Data monitor” mode with CONSULT-III.
2.
Check lifting switch (front) signal under the following conditions.
Is the indication normal?
YES
>> Lifting switch (front) function is OK.
NO
>> Refer to
Diagnosis Procedure
INFOID:0000000003759129
1.
CHECK LIFTING SWITCH (FRONT) INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect power seat switch (driver side) connector.
3.
Check voltage between power seat switch (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK LIFTING SWITCH (FRONT) CIRCUIT
1.
Disconnect driver seat control unit connector.
2.
Check continuity between driver seat control unit harness connector and power seat switch (driver side)
harness connector.
3.
Check continuity between driver seat control unit harness connector and ground.
Monitor item
Condition
Status
LIFT FR SW-UP
Lifting switch front (up)
Operate
ON
Release
OFF
LIFT FR SW-DN
Lifting switch front (down)
Operate
ON
Release
OFF
(+)
(–)
Voltage (V)
(Approx.)
Power seat switch (driver side)
Connector
Terminal
B459
17
Ground
Battery voltage
18
Driver seat control unit
Power seat switch (driver side)
Continuity
Connector
Terminal
Connector
Terminal
B452
17
B459
17
Existed
18
18
Driver seat control unit
Ground
Continuity
Connector
Terminal
B452
17
Not existed
18
LIFTING SWITCH (FRONT)
ADP-51
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
Is the inspection result normal?
YES
>> Replace driver seat control unit. Refer to
ADP-136, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK LIFTING SWITCH (FRONT)
ADP-51, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace power seat switch (driver side). Refer to
ADP-138, "Removal and Installation"
.
4.
CHECK INTERMITTENT INCIDENT
GI-35, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000003759130
1.
CHECK LIFTING SWITCH (FRONT)
1.
Turn ignition switch OFF.
2.
Disconnect power seat switch (driver side) connector.
3.
Check continuity between power seat switch (driver side) terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace power seat switch (driver side). Refer to
ADP-138, "Removal and Installation"
.
Power seat switch (driver side)
Condition
Continuity
Terminal
36
17
Lifting switch front (down)
Operate
Existed
Release
Not existed
18
Lifting switch front (up)
Operate
Existed
Release
Not existed
ADP-52
< COMPONENT DIAGNOSIS >
LIFTING SWITCH (REAR)
LIFTING SWITCH (REAR)
Description
INFOID:0000000003759131
Lifting switch (rear) is equipped to the power seat switch on the seat cushion side surface. The operation sig-
nal is inputted to the driver seat control unit when the lifting switch (rear) is operated.
Component Function Check
INFOID:0000000003759132
1.
CHECK FUNCTION
1.
Select “LIFT RR SW-UP”, “LIFT RR SW-DN” in “Data monitor” mode with CONSULT-III.
2.
Check lifting switch (rear) signal under the following conditions.
Is the indication normal?
YES
>> Lifting switch (rear) function is OK.
NO
>> Refer to
Diagnosis Procedure
INFOID:0000000003759133
1.
CHECK LIFTING SWITCH (REAR) INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect power seat switch (driver side) connector.
3.
Check voltage between power seat switch (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK LIFTING SWITCH (REAR) CIRCUIT
1.
Disconnect driver seat control unit connector.
2.
Check continuity between driver seat control unit harness connector and power seat switch (driver side)
harness connector.
3.
Check continuity between driver seat control unit harness connector and ground.
Monitor item
Condition
Status
LIFT RR SW-UP
Lifting switch rear (up)
Operate
ON
Release
OFF
LIFT RR SW-DN
Lifting switch rear (down)
Operate
ON
Release
OFF
(+)
(–)
Voltage (V)
(Approx.)
Power seat switch (driver side)
Connector
Terminal
B459
15
Ground
Battery voltage
16
Driver seat control unit
Power seat switch (driver side)
Continuity
Connector
Terminal
Connector
Terminal
B452
15
B459
15
Existed
16
16
Driver seat control unit
Ground
Continuity
Connector
Terminal
B452
15
Not existed
16
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст