Nissan Teana J32. Instruction — part 12
B2112 SLIDING MOTOR
ADP-41
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
B2112 SLIDING MOTOR
Description
INFOID:0000000003759103
• The sliding motor is installed to the seat cushion frame.
• The sliding motor is activated via the driver seat control unit.
• Slides the seat forward/rearward by changing the rotation direction of sliding motor.
DTC Logic
INFOID:0000000003759104
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
STEP 1
1.
Turn ignition switch ON.
2.
Check “Self diagnostic result” with CONSULT-III.
Is the DTC detected?
YES
>> Refer to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000003759105
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check “Self diagnostic result” with CONSULT-III.
3.
Erase the DTC.
4.
Perform DTC confirmation procedure. Refer to
.
Is the DTC displayed again?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK SLIDING MOTOR CIRCUIT (POWER SHORT)
1.
Turn ignition switch OFF.
2.
Disconnect sliding motor connector and driver seat control unit connector.
3.
Check voltage between sliding motor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK DRIVER SEAT CONTROL UNIT OUTPUT SIGNAL
1.
Connect driver seat control unit connector.
2.
Check voltage between driver seat control unit harness connector and ground.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2112
SEAT SLIDE
The driver seat control unit detects the output of sliding
motor output terminal for 0.1 seconds or more even if
the sliding switch is not input
• Driver seat control unit
• Slide motor harness is shorted
(+)
(–)
Voltage (V)
(Approx.)
Sliding motor
Connector
Terminal
B461
3
Ground
0
4
ADP-42
< COMPONENT DIAGNOSIS >
B2112 SLIDING MOTOR
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace driver seat control unit. Refer to
ADP-136, "Removal and Installation"
4.
CHECK INTERMITTENT INCIDENT
GI-35, "Intermittent Incident"
>> INSPECTION END
(+)
(–)
Voltage (V)
(Approx.)
Driver seat control unit
Connector
Terminal
B451
3
Ground
0
4
B2113 RECLINING MOTOR
ADP-43
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
B2113 RECLINING MOTOR
Description
INFOID:0000000003759106
• The reclining motor is installed to the seatback frame.
• The reclining motor is activated via the driver seat control unit.
• Tilts the seatback forward/rearward by changing the rotation direction of reclining motor.
DTC Logic
INFOID:0000000003759107
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
STEP 1
1.
Turn ignition switch ON.
2.
Check “Self diagnostic result” with CONSULT-III.
Is the DTC detected?
YES
>> Refer to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000003759108
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check “Self diagnostic result” with CONSULT-III.
3.
Erase the DTC.
4.
Perform DTC confirmation procedure. Refer to
.
Is the DTC displayed again?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK RECLINING MOTOR CIRCUIT (POWER SHORT)
1.
Turn ignition switch OFF.
2.
Disconnect reclining motor connector and driver seat control unit connector.
3.
Check voltage between reclining motor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK DRIVER SEAT CONTROL UNIT OUTPUT SIGNAL
1.
Connect driver seat control unit connector.
2.
Check voltage between driver seat control unit harness connector and ground.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2113
SEAT RECLINING
The driver seat control unit detects the output of reclin-
ing motor output terminal for 0.1 second or more even
if the reclining switch is not input
• Driver seat control unit
• Reclining motor harness is shorted
(+)
(–)
Voltage (V)
(Approx.)
Reclining motor
Connector
Terminal
B454
5
Ground
0
6
ADP-44
< COMPONENT DIAGNOSIS >
B2113 RECLINING MOTOR
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace driver seat control unit. Refer to
ADP-136, "Removal and Installation"
4.
CHECK INTERMITTENT INCIDENT
GI-35, "Intermittent Incident"
>> INSPECTION END
(+)
(–)
Voltage (V)
(Approx.)
Driver seat control unit
Connector
Terminal
B451
5
Ground
0
6
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст