Nissan Teana J32. Instruction — part 1137
TM-72
< COMPONENT DIAGNOSIS >
[CVT: RE0F09B]
P0778 PRESSURE CONTROL SOLENOID B ELECTRICAL (SEC PRESSURE
SOLENOID VALVE)
P0778 PRESSURE CONTROL SOLENOID B ELECTRICAL (SEC PRES-
SURE SOLENOID VALVE)
Description
INFOID:0000000003848998
The pressure control solenoid valve B (secondary pressure solenoid valve) regulates the oil pump discharge
pressure to suit the driving condition in response to the signal sent from the TCM.
DTC Logic
INFOID:0000000003848999
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
Immediately after performing any “DTC CONFIRMATION PROCEDURE”, always turn ignition switch OFF.
Then wait at least 10 seconds before performing the next test.
1.
CHECK DTC DETECTION
With CONSULT-III
1.
Start engine.
2.
Drive vehicle and maintain the following conditions for at least 5 consecutive seconds.
3.
Perform “Self-Diagnostic Results” mode for “TRANSMISSION”.
With GST
Follow the procedure “With CONSULT-III”.
Is “P0778 PRS CNT SOL/B CIRC” detected?
YES
>> Go to
NO
>> Check intermittent incident. Refer to
GI-35, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000003849000
1.
CHECK PRESSURE CONTROL SOLENOID VALVE B (SECONDARY PRESSURE SOLENOID VALVE)
CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector.
3.
Check resistance between TCM vehicle side harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 2.
2.
CHECK HARNESS BETWEEN TCM AND PRESSURE CONTROL SOLENOID VALVE B (SECONDARY
PRESSURE SOLENOID VALVE) (PART 1)
1.
Disconnect CVT unit connector.
2.
Check continuity between TCM vehicle side harness connector terminal and CVT unit vehicle side har-
ness connector terminal.
DTC
Item
(CONSULT-III screen term)
Malfunction is detected when...
Possible cause
P0778
PRS CNT SOL/B CIRC
• Normal voltage is not applied to solenoid
due to cut line, short, etc.
• TCM detects as irregular by comparing
target value with monitor value.
• Harness or connectors
(Solenoid circuit is open or shorted.)
• Pressure control solenoid valve B (sec-
ondary pressure solenoid valve)
TCM vehicle side harness connector
Ground
Resistance (Approx.)
Connector
Terminal
F23
39
3.0 – 9.0
Ω
P0778 PRESSURE CONTROL SOLENOID B ELECTRICAL (SEC PRESSURE
SOLENOID VALVE)
TM-73
< COMPONENT DIAGNOSIS >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK HARNESS BETWEEN TCM AND PRESSURE CONTROL SOLENOID VALVE B (SECONDARY
PRESSURE SOLENOID VALVE) (PART 2)
Check continuity between TCM vehicle side harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace damaged parts.
4.
CHECK PRESSURE CONTROL SOLENOID VALVE B (SECONDARY PRESSURE SOLENOID VALVE)
Check pressure control solenoid valve B (secondary pressure solenoid valve). Refer to
Inspection [Pressure Control Solenoid Valve B (Secondary Pressure Solenoid Valve)]"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace transaxle assembly. Refer to
5.
DETECT MALFUNCTIONING ITEMS
Check TCM connector pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
NO
>> Repair or replace damaged parts.
Component Inspection [Pressure Control Solenoid Valve B (Secondary Pressure So-
lenoid Valve)]
INFOID:0000000003849001
1.
CHECK PRESSURE CONTROL SOLENOID VALVE B (SECONDARY PRESSURE SOLENOID VALVE)
Check resistance between CVT unit connector terminal and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace transaxle assembly. Refer to
TCM vehicle side harness connector
CVT unit vehicle side harness connector
Continuity
Connector
Terminal
Connector
Terminal
F23
39
F24
3
Existed
TCM vehicle side harness connector
Ground
Continuity
Connector
Terminal
F23
39
Not existed
CVT unit connector
Ground
Resistance (Approx.)
Connector
Terminal
F24
3
3.0 – 9.0
Ω
TM-74
< COMPONENT DIAGNOSIS >
[CVT: RE0F09B]
P0840 TRANSMISSION FLUID PRESSURE SENSOR A (SEC PRESSURE SEN-
SOR)
P0840 TRANSMISSION FLUID PRESSURE SENSOR A (SEC PRESSURE
SENSOR)
Description
INFOID:0000000003849002
The transmission fluid pressure sensor A (secondary pressure sensor) detects secondary pressure of CVT
and sends the signal to the TCM.
DTC Logic
INFOID:0000000003849003
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
NOTE:
Immediately after performing any “DTC CONFIRMATION PROCEDURE”, always turn ignition switch OFF.
Then wait at least 10 seconds before performing the next test.
1.
CHECK DTC DETECTION
With CONSULT-III
1.
Turn ignition switch ON.
2.
Select “Data Monitor” mode for “TRANSMISSION”.
3.
Make sure that output voltage of CVT fluid temperature sensor is within the range below.
4.
Start engine and wait for at least 5 consecutive seconds.
With GST
Follow the procedure “With CONSULT-III”.
Is “P0840 TR PRS SENS/A CIRC” detected?
YES
>> Go to
NO
>> Check intermittent incident. Refer to
GI-35, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000003849004
1.
CHECK INPUT SIGNAL
1.
Start engine.
2.
Check voltage between TCM connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> GO TO 2.
2.
CHECK POWER AND SENSOR GROUND
Check voltage between TCM connector terminals.
DTC
Item
(CONSULT-III screen term)
Malfunction is detected when...
Possible cause
P0840
TR PRS SENS/A CIRC
Signal voltage of the transmission fluid pres-
sure sensor A (secondary pressure sensor)
is too high or too low while driving.
• Harness or connectors
(Sensor circuit is open or shorted.)
• Transmission fluid pressure sensor A
(secondary pressure sensor)
ATF TEMP SEN
: 1.0 – 2.0 V
If it is out of range, drive the vehicle to decrease the voltage (warm up the fluid) or stop engine to increase the voltage
(cool down the fluid)
TCM connector
Ground
Condition
Voltage (Approx.)
Connector
Terminal
F23
15
“N” position idle
1.0 - 1.5 V
P0840 TRANSMISSION FLUID PRESSURE SENSOR A (SEC PRESSURE SEN-
SOR)
TM-75
< COMPONENT DIAGNOSIS >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 5.
3.
CHECK HARNESS BETWEEN TCM AND CVT UNIT [TRANSMISSION FLUID PRESSURE SENSOR A
(SECONDARY PRESSURE SENSOR)] (PART 1)
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector and CVT unit connector.
3.
Check continuity between TCM vehicle side harness connector terminal and CVT unit vehicle side har-
ness connector terminal.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace damaged parts.
4.
CHECK HARNESS BETWEEN TCM AND CVT UNIT [TRANSMISSION FLUID PRESSURE SENSOR A
(SECONDARY PRESSURE SENSOR)] (PART 2)
Check continuity between TCM vehicle side harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace damaged parts.
5.
CHECK HARNESS BETWEEN TCM AND CVT UNIT (SENSOR POWER AND SENSOR GROUND) (PART
1)
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector and CVT unit connector.
3.
Check continuity between TCM vehicle side harness connector terminals and CVT unit vehicle side har-
ness connector terminals.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace damaged parts.
6.
CHECK HARNESS BETWEEN TCM AND CVT UNIT (SENSOR POWER AND SENSOR GROUND) (PART
2)
Check continuity between TCM vehicle side harness connector terminals and ground.
TCM connector
Voltage (Approx.)
Connector
Terminal
(+)
(-)
F23
26
25
4.75 - 5.25 V
TCM vehicle side harness connector
CVT unit vehicle side harness connector
Continuity
Connector
Terminal
Connector
Terminal
F23
15
F24
23
Existed
TCM vehicle side harness connector
Ground
Continuity
Connector
Terminal
F23
15
Not existed
TCM vehicle side harness connector
CVT unit vehicle side harness connector
Continuity
Connector
Terminal
Connector
Terminal
F23
25
F24
19
Existed
26
20
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст