Nissan Teana J32. Instruction — part 1136
TM-68
< COMPONENT DIAGNOSIS >
[CVT: RE0F09B]
P0746 PRESSURE CONTROL SOLENOID A PERFORMANCE (LINE PRESSURE
SOLENOID VALVE)
P0746 PRESSURE CONTROL SOLENOID A PERFORMANCE (LINE
PRESSURE SOLENOID VALVE)
Description
INFOID:0000000003848989
The pressure control solenoid valve A (line pressure solenoid valve) regulates the oil pump discharge pres-
sure to suit the driving condition in response to the signal sent from the TCM.
DTC Logic
INFOID:0000000003848990
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
Immediately after performing any “DTC CONFIRMATION PROCEDURE”, always turn ignition switch OFF.
Then wait at least 10 seconds before performing the next test.
1.
CHECK DTC DETECTION
With CONSULT-III
1.
Turn ignition switch ON.
2.
Select “Data Monitor” mode for “TRANSMISSION”.
3.
Start engine and maintain the following conditions for at least 10 consecutive seconds. Test start from 0
km/h (0 MPH).
With GST
Follow the procedure “With CONSULT-III”.
Is “P0746 PRS CNT SOL/A FCTN” detected?
YES
>> Go to
NO
>> Check intermittent incident. Refer to
GI-35, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000003848991
1.
CHECK LINE PRESSURE
Perform line pressure test. Refer to
TM-146, "Inspection and Judgment"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace damaged parts. Refer to
TM-146, "Inspection and Judgment"
.
2.
CHECK PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE)
1.
Turn ignition switch OFF.
2.
Disconnect CVT unit connector.
DTC
Item
(CONSULT-III screen term)
Malfunction is detected when...
Possible cause
P0746
PRS CNT SOL/A FCTN
Unexpected gear ratio was detected in the
low side due to excessively low line pres-
sure.
• Line pressure control system
• Output speed sensor (secondary speed
sensor)
• Input speed sensor (primary speed sen-
sor)
ATF TEMP SEN
: 1.0
−
2.0 V
ACC PEDAL OPEN
: More than 1.0/8
RANGE
: “D” position
VEHICLE SPEED
: 10 km/h (6 MPH) or more
Driving location
: Driving the vehicle uphill (increased engine load) will help maintain the driving
conditions required for this test.
P0746 PRESSURE CONTROL SOLENOID A PERFORMANCE (LINE PRESSURE
SOLENOID VALVE)
TM-69
< COMPONENT DIAGNOSIS >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
3.
Check pressure control solenoid valve A (line pressure solenoid valve). Refer to
Inspection [Pressure Control Solenoid Valve A (Line Pressure Solenoid Valve)]"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace transaxle assembly. Refer to
3.
CHECK OUTPUT SPEED SENSOR (SECONDARY SPEED SENSOR) SYSTEM
Check output speed sensor (secondary speed sensor) system. Refer to
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace damaged parts.
4.
CHECK INPUT SPEED SENSOR (PRIMARY SPEED SENSOR) SYSTEM
Check input speed sensor (primary speed sensor) system. Refer to
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace damaged parts.
5.
DETECT MALFUNCTIONING ITEMS
Check TCM connector pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
NO
>> Repair or replace damaged parts.
Component Inspection [Pressure Control Solenoid Valve A (Line Pressure Solenoid
Valve)]
INFOID:0000000003848992
1.
CHECK PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE)
Check resistance between CVT unit connector terminal and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace transaxle assembly. Refer to
CVT unit connector
Ground
Resistance (Approx.)
connector
Terminal
F24
2
3.0 – 9.0
Ω
TM-70
< COMPONENT DIAGNOSIS >
[CVT: RE0F09B]
P0776 PRESSURE CONTROL SOLENOID B PERFORMANCE (SEC PRESSURE
SOLENOID VALVE)
P0776 PRESSURE CONTROL SOLENOID B PERFORMANCE (SEC PRES-
SURE SOLENOID VALVE)
Description
INFOID:0000000003848993
The pressure control solenoid valve B (secondary pressure solenoid valve) regulates the secondary pressure
to suit the driving condition in response to the signal sent from the TCM.
DTC Logic
INFOID:0000000003848994
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
Immediately after performing any “DTC CONFIRMATION PROCEDURE”, always turn ignition switch OFF.
Then wait at least 10 seconds before performing the next test.
1.
CHECK DTC DETECTION
With CONSULT-III
1.
Turn ignition switch ON.
2.
Select “Data Monitor” mode for “TRANSMISSION”.
3.
Start engine and maintain the following conditions for at least 30 consecutive seconds.
With GST
Follow the procedure “With CONSULT-III”.
Is “P0776 PRS CNT SOL/B FCTN” detected?
YES
>> Go to
NO
>> Check intermittent incident. Refer to
GI-35, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000003848995
1.
CHECK LINE PRESSURE
Perform line pressure test. Refer to
TM-146, "Inspection and Judgment"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace damaged parts. Refer to
TM-146, "Inspection and Judgment"
.
2.
CHECK PRESSURE CONTROL SOLENOID VALVE B (SECONDARY PRESSURE SOLENOID VALVE)
1.
Turn ignition switch OFF.
2.
Disconnect CVT unit connector.
DTC
Item
(CONSULT-III screen term)
Malfunction is detected when...
Possible cause
P0776
PRS CNT SOL/B FCTN
Secondary pressure is too high or too low
compared with the commanded value while
driving.
• Harness or connectors
(Solenoid circuit is open or shorted.)
• Pressure control solenoid valve B (sec-
ondary pressure solenoid valve system)
• Transmission fluid pressure sensor A
(secondary pressure sensor)
• Line pressure control system
ATF TEMP SEN
: 1.0
−
2.0 V
ACC PEDAL OPEN
: More than 1.0/8
RANGE
: “D” position
VEHICLE SPEED
: 10 km/h (6 MPH) or more
Driving location
: Driving the vehicle uphill (increased engine load) will help maintain the driving
conditions required for this test.
P0776 PRESSURE CONTROL SOLENOID B PERFORMANCE (SEC PRESSURE
SOLENOID VALVE)
TM-71
< COMPONENT DIAGNOSIS >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
3.
Check pressure control solenoid valve B (secondary pressure solenoid valve). Refer to
nent Inspection [Pressure Control Solenoid Valve B (Secondary Pressure Solenoid Valve)]"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace transaxle assembly. Refer to
3.
CHECK PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE)
Check pressure control solenoid valve A (line pressure solenoid valve). Refer to
tion [Pressure Control Solenoid Valve A (Line Pressure Solenoid Valve)]"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace transaxle assembly. Refer to
4.
CHECK TRANSMISSION FLUID PRESSURE SENSOR A (SECONDARY PRESSURE SENSOR) SYS-
TEM
Check transmission fluid pressure sensor A (secondary pressure sensor) system. Refer to
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace damaged parts.
5.
DETECT MALFUNCTIONING ITEMS
Check TCM connector pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
NO
>> Repair or replace damaged parts.
Component Inspection [Pressure Control Solenoid Valve A (Line Pressure Solenoid
Valve)]
INFOID:0000000003848996
1.
CHECK PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE)
Check resistance between CVT unit connector terminal and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace transaxle assembly. Refer to
Component Inspection [Pressure Control Solenoid Valve B (Secondary Pressure So-
lenoid Valve)]
INFOID:0000000003848997
1.
CHECK PRESSURE CONTROL SOLENOID VALVE B (SECONDARY PRESSURE SOLENOID VALVE)
Check resistance between CVT unit connector terminal and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace transaxle assembly. Refer to
CVT unit connector
Ground
Resistance (Approx.)
Connector
Terminal
F24
2
3.0 – 9.0
Ω
CVT unit connector
Ground
Resistance (Approx.)
connector
Terminal
F24
3
3.0 – 9.0
Ω
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст