Nissan Teana J32. Instruction — part 1214
VTL-42
< ON-VEHICLE REPAIR >
[WITHOUT 7 INCH DISPLAY]
AIR MIX DOOR MOTOR
2.
Remove mounting screws (A), and then move foot duct (passen-
ger side) (1) to a position where it does not inhibit work.
3.
Remove mounting screws (B), and then remove air mix door
motor (passenger side) (2).
4.
Disconnect air mix door motor connector (passenger side).
INSTALLATION
Installation is basically the reverse order of removal.
JPIIA0924ZZ
HEATER CORE
VTL-43
< ON-VEHICLE REPAIR >
[WITHOUT 7 INCH DISPLAY]
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
HEATER CORE
Exploded View
INFOID:0000000003821362
1.
Ventilator seal
2.
Defroster seal
3.
Distributor upper case
4.
Center case
5.
Heater & cooling unit case cover
6.
Foot duct 1 (right)
7.
Foot duct 2 (right)
8.
Air mix door motor (passenger side)
9.
Evaporator pipe assembly
10.
Expansion valve
11.
O-ring
12. Evaporator
13.
Filter cover
14.
Air conditioner filter
15. Case packing
16.
Heater & cooling unit case (right)
17.
Cooler pipe grommet
18. Grommet
19.
Heater pipe grommet
20.
Heater pipe support
21. Drain hose
22.
Heater & cooling unit case (left)
23.
Air mix door motor (driver side)
24. Heater core
25.
Heater pipe cover
26.
Foot duct 2 (left)
27. Foot duct 1 (left)
28.
Aspirator hose
29.
Aspirator
30. Mode door motor
31.
Main link
32.
Rod link
33. Ventilator door link
34.
Mode door lever
35.
Ventilator door lever
36. Max. cool door link
JPIIA0906GB
VTL-44
< ON-VEHICLE REPAIR >
[WITHOUT 7 INCH DISPLAY]
HEATER CORE
Removal and Installation
INFOID:0000000003774686
REMOVAL
1.
Remove heater & cooling unit assembly. Refer to
.
2.
Remove mounting screws (A), and then remove foot duct (left)
(1).
3.
Remove heater pipe grommet (1).
4.
Remove mounting screw (A), and then remove heater pipe sup-
port (2).
5.
Remove mounting screws (B), and then remove heater pipe
cover (3).
6.
Slide heater core (1) to leftward (as shown in the figure).
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
• Replace O-rings with new ones. Then apply compressor oil to them when installing.
• Check for refrigerant leakage when charging refrigerant.
NOTE:
• Refer to
when filling radiator with engine coolant.
• Charge the refrigerant.
37. Defroster door link
38.
Foot door link
39.
Max. cool door lever
40. Foot door lever
41.
Defroster door lever
42.
Adapter case
43. Distributor lower case
44.
Ventilator door
45.
Intake sensor
46. Intake sensor bracket
47.
Foot door
48.
Max. cool door
49. Defroster door
50.
Air mix door (Slide door)
for symbols in the figure.
JPIIA0925ZZ
JPIIA0926ZZ
JPIIA0927ZZ
DUCT AND GRILLE
VTL-45
< ON-VEHICLE REPAIR >
[WITHOUT 7 INCH DISPLAY]
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
DUCT AND GRILLE
CENTER VENTILATOR GRILLE
CENTER VENTILATOR GRILLE : Exploded View
INFOID:0000000003774687
CENTER VENTILATOR GRILLE : Removal and Installation
INFOID:0000000003774688
REMOVAL
1.
Remove cluster lid D. Refer to
.
2.
Disengage the pawls, and then remove center ventilator grilles
(left and right) (1).
INSTALLATION
Installation is basically the reverse order of removal.
SIDE VENTILATOR GRILLE
1.
Side defroster nozzle (right)
2.
Defroster nozzle
3.
Side defroster nozzle (left)
4.
Ventilator duct
5.
Side defroster grille (left)
6.
Instrument panel assembly
7.
Side ventilator grille (left)
8.
Center ventilator grille (left)
9.
Cluster lid D
10. Center ventilator grille (right)
11. Side ventilator grille (right)
12. Side defroster grille (right)
JPIIA0928ZZ
: Pawl
JPIIA0929ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст