Nissan Teana J32. Instruction — part 1213
VTL-38
< ON-VEHICLE REPAIR >
[WITHOUT 7 INCH DISPLAY]
HEATER & COOLING UNIT ASSEMBLY
8.
Remove mounting bolts (A) from heater & cooling unit assembly and blower unit.
9.
Remove steering column mounting nuts (B). Refer to
10. Remove ground bolts (C) from steering member (1).
11. Disconnect each harness connectors, and remove harness clips from steering member.
12. Remove mounting bolts (A), and then remove steering member (1).
13. Disconnect the intake door motor and blower motor connectors.
14. Remove mounting screws (A), and then remove blower unit (1).
15. Disconnect drain hose (1) from heater & cooling unit assembly.
JPIIA0917ZZ
JPIIA0918ZZ
JPIIA0919ZZ
JPIIA0920ZZ
HEATER & COOLING UNIT ASSEMBLY
VTL-39
< ON-VEHICLE REPAIR >
[WITHOUT 7 INCH DISPLAY]
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
16. Remove floor duct 1 (left and right) (1) and rear ventilator duct 1
(2), and then remove heater & cooling unit assembly (3).
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
• Replace O-rings with new ones. Then apply compressor oil to them when installing.
• Check for leakages when recharging refrigerant.
NOTE:
• Refer to
when filling radiator with engine coolant.
• Charge the refrigerant.
JPIIA0921ZZ
VTL-40
< ON-VEHICLE REPAIR >
[WITHOUT 7 INCH DISPLAY]
MODE DOOR MOTOR
MODE DOOR MOTOR
Exploded View
INFOID:0000000003774681
Removal and Installation
INFOID:0000000003774682
REMOVAL
1.
Remove BCM. Refer to
.
2.
Remove mounting screws (A), and then remove mode door
motor (1).
3.
Disconnect mode door motor connector.
INSTALLATION
Installation is basically the reverse order of removal.
1.
Heater & cooling unit assembly
2.
Air mix door motor (passenger side)
3.
Air mix door motor (driver side)
4.
Mode door motor
5.
Main link
6.
Rod link
7.
Mode door lever
8.
Ventilator door link
9.
Foot door link
10. Foot door lever
11.
Max. cool door link
12.
Max. cool door lever
13. Defroster door link
14.
Defroster door lever
JPIIA0922ZZ
JPIIA0923ZZ
AIR MIX DOOR MOTOR
VTL-41
< ON-VEHICLE REPAIR >
[WITHOUT 7 INCH DISPLAY]
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
AIR MIX DOOR MOTOR
Exploded View
INFOID:0000000003821360
Removal and Installation
INFOID:0000000003774684
REMOVAL
Driver Side
1.
Disconnect the battery cable from the negative terminal after setting the temperature (driver side) to 18
°
C
(60
°
F).
2.
Remove foot duct (driver side). Refer to
VTL-59, "FOOT DUCT : Exploded View"
3.
Remove mounting screws (A), and then remove air mix door
motor (driver side) (1).
4.
Disconnect air mix door motor connector (driver side).
Passenger Side
1.
Disconnect the battery cable from the negative terminal after setting the temperature (passenger side) to
18
°
C (60
°
F).
1.
Heater & cooling unit assembly
2.
Air mix door motor (passenger side)
3.
Air mix door motor (driver side)
4.
Mode door motor
5.
Main link
6.
Rod link
7.
Mode door lever
8.
Ventilator door link
9.
Foot door link
10.
Foot door lever
11.
Max. cool door link
12. Max. cool door lever
13.
Defroster door link
14.
Defroster door lever
JPIIA0922ZZ
JPIIA0577ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст