Nissan Teana J32. Instruction — part 1032
SEC-116
< COMPONENT DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
SECURITY INDICATOR LAMP
3.
CHECK SECURITY INDICATOR LAMP
SEC-116, "Component Inspection"
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-78, "Removal and Installation"
NO
>> Replace combination meter. Refer to
MWI-126, "Removal and Installation"
Component Inspection
INFOID:0000000003815073
1.
CHECK SECURITY INDICATOR LAMP
1.
Disconnect combination meter connector.
2.
Check continuity between combination meter terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace combination meter. Refer to
MWI-126, "Removal and Installation"
Terminal
Continuity
Combination meter
(+)
(–)
1
28
Existed
28
1
Not existed
KEY WARNING LAMP
SEC-117
< COMPONENT DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
KEY WARNING LAMP
Description
INFOID:0000000003815074
• Key warning lamp is located on combination meter.
• Performs operation method guide and warning together with buzzer.
Component Function Check
INFOID:0000000003815075
1.
CHECK FUNCTION
Check the operation with “INDICATOR” in “Active Test” mode with CONSULT-III.
Is the inspection result normal?
YES
>> Key warning lamp in combination meter is OK.
NO
>> Refer to
SEC-117, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000003815076
1.
CHECK KEY WARNING LAMP
.
Is the inspection result normal?
Yes
>> GO TO 2.
No
>> Repair or replace key warning lamp circuit.
2.
CHECK INTERMITTENT INCIDENT
GI-35, "Intermittent Incident"
.
>> INSPECTION END
Test item
Condition
INDICATOR
RED ON
Key warning lamp (red) illuminates
RED IND
Key warning lamp (red) blinks
SEC-118
< COMPONENT DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
HORN FUNCTION
HORN FUNCTION
Description
INFOID:0000000003840063
Perform answer-back for each operation with horn.
Component Function Check
INFOID:0000000003840064
1.
CHECK FUNCTION
1.
Select “HORN” in “ACTIVE TEST” mode with CONSULT-III.
2.
Check the horn (high/low) operation.
Is the operation normal?
YES
>> Horn function is OK.
NO
>> Go to
SEC-118, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000003840065
1.
CHECK HORN FUNCTION
Check horn function with horn switch
Do the horns sound?
YES
>> GO TO 2.
NO
>> Go to
HRN-2, "Wiring Diagram - HORN -"
2.
CHECK HORN RELAY POWER SUPPLY
1.
Turn ignition switch ON.
2.
Perform “ACTIVE TEST” (“HORN”) with CONSULT-Ill.
3.
Check voltage between horn relayconnector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 3.
3.
CHECK HORN RELAY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector and horn relay.
3.
Check continuity between IPDM E/R harness connector and horn relay connector.
4.
Check continuity between driver seat control unit harness connector and ground.
Is the inspection result normal?
Test item
Description
HORN
ON
Horn relay
ON (for 20 ms)
Horn relay
Ground
Test item
Voltage (V)
(Approx.)
Connector
Terminal
E5
1
HORN
ON
Battery voltage
→
0
→
Battery voltage
Other than above
Battery voltage
IPDM E/R
Horn relay
Continuity
Connector
Terminal
Connector
Terminal
E11
44
E5
1
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E11
44
Not existed
HORN FUNCTION
SEC-119
< COMPONENT DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
YES
>> Replace IPDM E/R. Refer to
PCS-34, "Removal and Installation"
.
NO
>> Repair or replace harness.
4.
CHECK INTERMITTENT INCIDENT
GI-35, "Intermittent Incident"
.
Is the inspection result normal?
>> INSPECTION END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст