Nissan Teana J32. Instruction — part 357
REAR DOOR
DLK-211
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Remove rear door hinge mounting bolts and nuts (body side), and then remove door hinge.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check rear door open/close, lock/unlock operation after installation.
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installation, rear door assembly, perform the fitting adjustment. Refer to
.
• After installing, apply the touch-up paint (the body color) onto the head of door hinge mounting nuts.
DOOR CHECK LINK
DOOR CHECK LINK : Exploded View
INFOID:0000000003819609
DOOR CHECK LINK : Removal and Installation
INFOID:0000000003813411
REMOVAL
1.
Remove rear door finisher. Refer to
INT-36, "Removal and Installation"
.
2.
Fully close the rear door window.
3.
Remove rear door speaker.
4.
Remove mounting bolts of the door link on the vehicle.
5.
Remove mounting bolts of the door link on door panel.
6.
Take door check link out from the hole of door panel.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
1.
Rear door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Door check link
7.
Door hinge (lower)
8.
Door hinge (upper)
Refer to
JMKIA2385ZZ
DLK-212
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR
Check rear door open/close operation after installation.
TRUNK LID
DLK-213
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
TRUNK LID
TRUNK LID ASSEMBLY
TRUNK LID ASSEMBLY : Exploded View
INFOID:0000000003813412
REMOVAL
ADJUSTMENT
1.
Trunk lid
2.
Trunk lid weather-strip
3.
Cap
4.
Stopper
5.
Trunk lid hinge
6.
Trunk lid striker
7.
Bumper rubber
8.
Trunk lid lock assembly
9.
Trunk lid stay
A
: Center mark (upper)
B.
: Center mark (lower)
Refer to
for symbols in the figure.
JMKIA2389GB
DLK-214
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
TRUNK LID
TRUNK LID ASSEMBLY : Removal and Installation
INFOID:0000000003813413
CAUTION:
Operate with two workers, because of its heavy weight.
REMOVAL
1.
Remove the trunk lid finisher inner. Refer to
INT-59, "Removal and Installation"
2.
Disconnect the connectors in the trunk lid, and remove the harness clamps to pull the harness out of the
trunk lid.
3.
Remove trunk lid stay at trunk lid side. Refer to
DLK-218, "TRUNK LID STAY : Removal and Installation"
.
4.
Remove the trunk lid hinge mounting bolts on trunk lid side and remove the trunk lid assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• After installing, apply touch-up paint (the body color) onto the head of the hinge mounting bolts.
• Check trunk lid open/close, lock/unlock operation after installation.
• After installation, perform fitting adjustment. Refer to
DLK-215, "TRUNK LID ASSEMBLY : Adjust-
1.
Trunk lid assembly
2.
Trunk lid hinge
3.
Trunk lid striker
4.
Body side outer
5.
Rear combination lamp
6.
Rear bumper fascia
Refer to
for symbols in the figure.
JMKIA2393GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст