Nissan Teana J32. Instruction — part 621
FRONT COIL SPRING AND STRUT
FSU-9
< ON-VEHICLE REPAIR >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
ON-VEHICLE REPAIR
FRONT COIL SPRING AND STRUT
Exploded View
INFOID:0000000003811116
Removal and Installation
INFOID:0000000003811117
REMOVAL
1.
Remove tires.
2.
Remove lock plate of brake hose. Refer to
BR-19, "FRONT : Exploded View"
3.
Remove wheel sensor. Refer to
BRC-57, "FRONT WHEEL SENSOR : Exploded View"
BRC-151, "FRONT WHEEL SENSOR : Exploded View"
4.
Remove stabilizer connecting rod from strut assembly. Refer to
.
5.
Remove strut assembly from steering knuckle.
6.
Remove cowl top cover. Refer to
7.
Remove mounting bolts of strut mounting insulator, and then remove strut assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Become it in projection (A) an illustration to the vehicle outside.
• Perform final tightening of bolts and nuts, under unladen conditions
with tires on level ground.
1.
Strut mounting insulator
2.
Strut mounting bearing
3.
Coil spring
4.
Bound bumper
5.
Lower rubber seat
6.
Strut
Refer to
JPEIA0112GB
: Vehicle front
JPEIA0094ZZ
FSU-10
< ON-VEHICLE REPAIR >
FRONT COIL SPRING AND STRUT
Disassembly and Assembly
INFOID:0000000003811118
DISASSEMBLY
CAUTION:
Never damage strut assembly piston rod when removing components from strut assembly.
1.
Install strut attachment (A) (SST: ST35652000) to strut assem-
bly and secure it in a vise.
CAUTION:
When installing the strut attachment to strut assembly,
wrap a shop cloth around strut to protect from damage.
2.
Using a spring compressor (A) (commercial service tool), com-
press coil spring between strut mounting bearing and lower rub-
ber seat (on strut assembly) until coil spring with a spring
compressor is free.
CAUTION:
Be sure a spring compressor is securely attached to coil
spring. Compress coil spring.
3.
Make sure coil spring with a spring compressor between strut
mounting bearing and lower rubber seat (strut assembly) is free.
And then remove piston rod lock nut while securing the piston
rod tip so that piston rod does not turn.
4.
Remove strut mounting insulator and strut mounting bearing,
and bound bumper from strut.
5.
After remove coil spring with a spring compressor, and then gradually release a spring compressor.
CAUTION:
Loosen while making sure coil spring attachment position does not move.
6.
Remove lower rubber seat from strut.
7.
Remove the strut attachment (SST: ST35652000) from strut.
ASSEMBLY
1.
Install strut attachment (SST: ST35652000) to strut and secure it in a vise.
CAUTION:
When installing the strut attachment to strut assembly, wrap a shop cloth around strut to protect
from damage.
2.
Install lower rubber seat.
3.
Install bound bumper onto strut mounting insulator.
4.
Compress coil spring using a spring compressor (commercial service tool), and install it onto strut assem-
bly.
CAUTION:
• Face tube side of coil spring (1) downward. Align the
lower end (A) to lower rubber seat (2).
• Be sure a compressor is securely attached to coil spring.
Compress coil spring.
• Set coil spring so that its paint marks are aligned with the
positions of 1.25 turns and 2.25 turns from the bottom end
of the coil spring.
JPEIA0006ZZ
JPEIA0007ZZ
JPEIA0095ZZ
FRONT COIL SPRING AND STRUT
FSU-11
< ON-VEHICLE REPAIR >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
5.
Install strut mounting bearing and strut mounting insulator with bound bumper to strut.
• Installation position of strut mounting insulator is shown in the
figure.
CAUTION:
Become it in projection (A) to the vehicle outside.
6.
Secure piston rod tip so that piston rod does not turn, then
tighten piston rod lock nut with specified torque.
CAUTION:
Never reuse piston rod lock nut.
7.
Gradually release a spring compressor, and remove coil spring.
CAUTION:
Loosen while making sure coil spring attachment position does not move.
8.
Remove the strut attachment from strut assembly.
Inspection
INFOID:0000000003811119
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
(without VDC),
BRC-151, "FRONT WHEEL SENSOR : Exploded View"
(with VDC).
2.
Check wheel alignment. Refer to
FSU-7, "Wheel Alignment Inspection"
.
3.
Adjust neutral position of steering angle sensor (with VDC). Refer to
STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
INSPECTION AFTER DISASSEMBLY
Strut
Check the following items, and replace if necessary.
• Strut for deformation, cracks or damage
• Piston rod for damage, uneven wear or distortion
• Oil leakage
Strut Mounting Insulator and Rubber Parts Inspection
Check strut mounting insulator for cracks and rubber parts for wear. Replace if necessary.
Coil Spring
Check coil spring for cracks, wear or damage. Replace if necessary.
: Vehicle front
JPEIA0094ZZ
FSU-12
< ON-VEHICLE REPAIR >
TRANSVERSE LINK
TRANSVERSE LINK
Exploded View
INFOID:0000000003811120
Removal and Installation
INFOID:0000000003811121
REMOVAL
1.
Remove tires.
2.
Remove drive shaft of wheel side from wheel hub and bearing assembly. Refer to
.
3.
Remove transverse link from steering knuckle.
4.
Remove transverse link from suspension member.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of bolts and nuts at the front suspension member, under unladen conditions with
tires on level ground.
Inspection
INFOID:0000000003811122
INSPECTION AFTER REMOVAL
Appearance
Check the following:
• Transverse link and bushing for deformation, cracks or damage. Replace if necessary.
• Ball joint boot for cracks or other damage, and also for grease leakage. Replace if necessary.
Ball Joint Inspection
Instructionly move ball stud to confirm it moves smoothly with no binding.
Swing Torque Inspection
NOTE:
Before measurement, move ball stud at least ten times by hand to check for smooth movement.
1.
Transverse link
2.
Front suspension member
Refer to
for symbols in the figure.
JPEIA0100GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст