Nissan Teana J32. Instruction — part 622
TRANSVERSE LINK
FSU-13
< ON-VEHICLE REPAIR >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
• Hook a spring balance (A) at cotter pin mounting hole. Confirm
spring balance measurement value is within specifications when
ball stud begins moving.
- If swing torque exceeds standard value, replace transverse link
assembly.
Rotating Torque Inspection
• Attach mounting nut to boll stud. Check that rotating torque is
within specifications with a preload gauge (A) (SST: ST3127S000).
- If rotating torque exceeds standard range, replace transverse link
assembly.
Axial End Play Inspection
• Move tip of ball stud in axial direction to check for looseness.
- If axial end play exceeds the standard value, replace transverse link assembly.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
(without VDC),
BRC-151, "FRONT WHEEL SENSOR : Exploded View"
(with VDC).
2.
Check wheel alignment. Refer to
FSU-7, "Wheel Alignment Inspection"
.
3.
Adjust neutral position of steering angle sensor (with VDC). Refer to
STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
Standard
Swing torque
Spring balance
measurement
JPEIA0005ZZ
Standard
Rotating torque
: Refer to
.
PDIA1258E
Standard
Axial end play
:Refer to
.
FSU-14
< ON-VEHICLE REPAIR >
FRONT STABILIZER
FRONT STABILIZER
Exploded View
INFOID:0000000003811123
Removal and Installation
INFOID:0000000003811124
REMOVAL
1.
Remove tires.
2.
Remove front exhaust tube. Refer to
3.
Remove stabilizer connecting rod.
4.
Remove steering gear assembly. Refer to
.
5.
Remove mounting bolts (
) of stabilizer clamp, and then
remove stabilizer clamp and stabilizer bushing from front sus-
pension member.
6.
Remove stabilizer bar.
INSTALLATION
Note the following, and install in the reverse order of removal.
1.
Stabilizer clamp
2.
Stabilizer bushing
3.
Stabilizer bar
4.
Front suspension member
5.
Stabilizer connecting rod
Refer to
for symbols in the figure.
JPEIA0101GB
WEIA0182E
FRONT STABILIZER
FSU-15
< ON-VEHICLE REPAIR >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
• Install stabilizer clamp that notch (A) becomes vehicle front side
(
).
• Install stabilizer bushing that slit (B) becomes vehicle front side
(
).
Inspection
INFOID:0000000003811125
INSPECTION AFTER REMOVAL
Check stabilizer bar, stabilizer connecting rod, stabilizer bushing and stabilizer clamp for deformation, cracks
or damage. Replace if necessary.
JPEIA0058ZZ
FSU-16
< REMOVAL AND INSTALLATION >
FRONT SUSPENSION MEMBER
REMOVAL AND INSTALLATION
FRONT SUSPENSION MEMBER
Exploded View
INFOID:0000000003811126
Removal and Installation
INFOID:0000000003811127
REMOVAL
1.
Remove tires.
2.
Remove under cover.
3.
Remove wheel sensor. Refer to
BRC-57, "FRONT WHEEL SENSOR : Exploded View"
BRC-151, "FRONT WHEEL SENSOR : Exploded View"
(with VDC).
4.
Remove lock plate of brake hose. Refer to
BR-19, "FRONT : Exploded View"
5.
Remove caliper assembly. Hang caliper assembly not to interfere with work. Refer to
CALIPER ASSEMBLY : Exploded View"
.
6.
Remove stabilizer connecting rod (upper side). Refer to
7.
Remove exhaust front tube. Refer to
8.
Remove power steering solenoid valve harness connector and harness clip. Refer to
.
9.
Remove heat insulator from suspension member.
10. Remove drive shaft. Refer to
FAX-18, "LEFT SIDE : Removal and Installation"
(left side),
SIDE : Removal and Installation"
11. Separate lower shaft and steering gear assembly. Refer to
12. Remove power steering oil pump and then separate suction hose and high pressure piping. Refer to
.
13. Separate engine mount insulator from engine assembly. Refer to
.
14. Set suitable jack to front suspension member.
15. Remove front suspension member stay.
16. Remove front suspension member mounting bolts.
17. Gradually lower the jack placed at the front suspension member.
CAUTION:
Perform the work while checking that the jack is stable.
1.
Front suspension member
2.
Rebound stopper
3.
Front suspension member stay
Refer to
for symbols in the figure.
JPEIA0102GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст