Nissan Teana J32. Instruction — part 812
MIR-12
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000003815741
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Instruction.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PREPARATION
MIR-13
< PREPARATION >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
PREPARATION
PREPARATION
Commercial Service Tools
INFOID:0000000003815742
Tool name
Description
Remover tool
Removes the clip and pawl and metal clip
PIIB7923J
MIR-14
< ON-VEHICLE REPAIR >
INSIDE MIRROR
ON-VEHICLE REPAIR
INSIDE MIRROR
Exploded View
INFOID:0000000003815743
Removal and Installation
INFOID:0000000003815744
REMOVAL
1.
Insert flat-headed screwdriver (A) under the inside mirror (1).
2.
Slide the inside mirror to the upper side while pushing the pawl
downward.
CAUTION:
Never use excessive force to remove the inside mirror because
it is inserted tightly into the mirror base.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
When inserting the inside mirror into the mirror base, be careful to push the pawl until it connects to
the mirror base.
1.
Inside mirror
2.
Mirror base
Refer to
for symbols in the figure.
JMLIA0145ZZ
JMLIA0055ZZ
OUTSIDE MIRROR
MIR-15
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
OUTSIDE MIRROR
DOOR MIRROR ASSEMBLY
DOOR MIRROR ASSEMBLY : Exploded View
INFOID:0000000003815745
DOOR MIRROR ASSEMBLY : Removal and Installation
INFOID:0000000003815746
REMOVAL
1.
Remove front door finisher. Refer to
INT-30, "DRIVER SIDE : Removal and Installation"
(driver side) or
INT-33, "PASSENGER SIDE : Removal and Installation"
(passenger side).
2.
Remove clips and remove corner cover.
3.
Disconnect door mirror harness connector.
4.
Remove door mirror mounting nuts, and remove door mirror assembly.
INSTALLATION
Install in the reverse order of removal.
DOOR MIRROR ASSEMBLY : Disassembly and Assembly
INFOID:0000000003815747
DISASSEMBLY
1.
Remove door mirror assembly. Refer to
MIR-15, "DOOR MIRROR ASSEMBLY : Removal and Installa-
2.
Remove glass mirror. Refer to
MIR-18, "GLASS MIRROR : Disassembly and Assembly"
3.
Remove door mirror cover. Refer to
MIR-19, "DOOR MIRROR COVER : Disassembly and Assembly"
.
1.
Door mirror cover
2.
Side turn signal lamp assembly
3.
Corner cover
4.
Glass mirror
5.
Mirror assembly
: Clip
: Pawl
JMLIA0157ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст