Nissan Teana J32. Instruction — part 813
MIR-16
< ON-VEHICLE REPAIR >
OUTSIDE MIRROR
4.
Remove screws (A) and connectors, and then remove actuator
(1).
5.
Using a flat-bladed screwdriver (A) and remove lower cover (1).
6.
Remove TORX bolts (A) and remove base assembly (1).
7.
Remove TORX bolts (A) and remove base bracket (1).
JMLIA0160ZZ
JMLIA0161ZZ
JMLIA0162ZZ
JMLIA0163ZZ
OUTSIDE MIRROR
MIR-17
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
8.
Using a flat-bladed screwdriver (A) and remove bracket cover
(1).
9.
Disconnect connector of side turn signal lamp assembly.
10. Remove screws (A) and remove bracket assembly (1).
11. Remove screws (A) and remove under body (1).
12. Remove screws (A) and remove side turn signal lamp assembly
(1).
ASSEMBLY
Assemble in the reverse order of disassembly.
GLASS MIRROR
JMLIA0164ZZ
JMLIA0165ZZ
JMLIA0166ZZ
JMLIA0167ZZ
MIR-18
< ON-VEHICLE REPAIR >
OUTSIDE MIRROR
GLASS MIRROR : Exploded View
INFOID:0000000003815765
GLASS MIRROR : Disassembly and Assembly
INFOID:0000000003815749
DISASSEMBLY
1.
Place the glass mirror upward.
2.
Put a strip of protective tape (B) on housing assembly.
3.
As shown in the figure, insert a small flat-bladed screwdriver (A)
between glass mirror (1) and actuator (2). Push up both pawls
simultaneously to remove glass mirror lower half side.
NOTE:
Insert screwdriver, and push up while rotating (twisting) to make
work easier.
4.
Remove two terminals of mirror heater attachment.
5.
Lightly lift up lower side of glass mirror, and detach both pawls of upper side as if pulling it out. Disassem-
ble glass mirror from actuator.
NOTE:
Be careful not to allow grease on sealing agent in center of mirror or back side of glass mirror.
ASSEMBLY
Assemble in the reverse order of disassembly.
1.
Door mirror cover
2.
Side turn signal lamp assembly
3.
Corner cover
4.
Glass mirror
5.
Mirror assembly
: Clip
: Pawl
JMLIA0157ZZ
JMLIA0158ZZ
OUTSIDE MIRROR
MIR-19
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
CAUTION:
After installation, visually check that pawls are securely engaged.
DOOR MIRROR COVER
DOOR MIRROR COVER : Exploded View
INFOID:0000000003815766
DOOR MIRROR COVER : Disassembly and Assembly
INFOID:0000000003815751
CAUTION:
Never damage the mirror bodies.
DISASSEMBLY
1.
Remove the glass mirror. Refer to
MIR-18, "GLASS MIRROR : Disassembly and Assembly"
2.
Remove the pawls, and disassemble the door mirror cover from
the mirror assembly.
ASSEMBLY
Assemble in the reverse order of disassembly.
1.
Door mirror cover
2.
Side turn signal lamp assembly
3.
Corner cover
4.
Glass mirror
5.
Mirror assembly
: Clip
: Pawl
JMLIA0157ZZ
JMLIA0159ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст