Nissan Teana J32. Instruction — part 3
DIAGNOSIS AND REPAIR WORKFLOW
ADP-5
< BASIC INSPECTION >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
1.
GET INFORMATION FOR SYMPTOM
Get detailed information from the customer about the symptom (the condition and the environment when the
incident/malfunction occurs).
>> GO TO 2.
2.
CHECK DTC WITH AUTOMATIC DRIVE POSITIONER SYSTEM
Check “Self Diagnostic Result” with CONSULT-III. Refer to
Are any symptoms described and any DTC displayed?
Symptom is described, DTC is detected.>>GO TO 3.
Symptom is not described, DTC is detected.>>GO TO 6.
Symptom is described, DTC is not detected.>>GO TO 4.
3.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
>> GO TO 6.
4.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
>> GO TO 5.
5.
CHECK NORMAL OPERATING CONDITION
Check normal operating condition. Refer to
.
Is the incident a normal operation?
YES
>> GO TO 10.
NO
>> GO TO 7.
6.
PERFORM DTC CONFIRMATION PROCEDURE
Perform the confirmation procedure for the detected DTC.
Is the DTC displayed?
YES
>> GO TO 8.
NO
>> Check intermittent incident. Refer to
GI-35, "Intermittent Incident"
.
7.
PERFORM COMPONENT FUNCTION CHECK
Perform the component function check for the isolated malfunctioning point.
>> GO TO 8.
8.
DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE
Isolate the malfunctioning point by performing the diagnosis procedure relevant to the symptom during the
component diagnosis.
>> GO TO 9.
9.
REPARE OR REPLACE
Repair or replace the malfunctioning part.
>> GO TO 10.
10.
FINAL CHECK
Perform the DTC confirmation procedure (if DTC is detected) or component function check (if no DTC is
detected) again. Check that the malfunction is repaired.
Are all malfunctions repaired?
ADP-6
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORKFLOW
YES
>> INSPECTION END
Symptom is detected.>> GO TO 5.
DTC is detected.>> GO TO 6.
INSPECTION AND ADJUSTMENT
ADP-7
< BASIC INSPECTION >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : De-
scription
INFOID:0000000003759058
Each function is reset to the following condition when the battery terminal is disconnected.
*1
: Default value is 40mm.
NOTE:
Notice that disconnecting the battery when detected DTC are present will erase the DTC memory.
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Spe-
cial Repair Requirement
INFOID:0000000003759059
1.
SYSTEM INITIALIZATION
Perform system initialization. Refer to
ADP-8, "SYSTEM INITIALIZATION : Description"
.
>> GO TO 2.
2.
SYSTEM SETTING
Perform system setting. Refer to
ADP-9, "SYSTEM SETTING : Description"
.
>> GO TO 3.
3.
MEMORY STORAGE
Perform memory storage. Refer to
ADP-8, "MEMORY STORING : Description"
.
>> END
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
INFOID:0000000003759060
Each function is reset to the following condition when the driver seat control unit is replaced.
*1
: Default value is 40 mm.
NOTE:
Notice that disconnecting the battery when detected DTC are present will erase the DTC memory.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
Function
Condition
Procedure
Memory (Seat)
Erased
Perform memory storage
Entry/exit assist
OFF
Perform system initialization
Set slide amount
*1
Intelligent Key interlock
Erased
Perform system initialization
Perform memory storage
Function
Condition
Procedure
Memory (Seat)
Erased
Perform memory storage
Entry/exit assist
OFF
Perform system initialization
Set slide amount
*1
Intelligent Key interlock
Erased
Perform system initialization
Perform memory storage
ADP-8
< BASIC INSPECTION >
INSPECTION AND ADJUSTMENT
quirement
INFOID:0000000003759061
1.
SYSTEM INITIALIZATION
Perform system initialization. Refer to
ADP-8, "SYSTEM INITIALIZATION : Description"
.
>> GO TO 2.
2.
SYSTEM SETTING
Perform system setting. Refer to
ADP-9, "SYSTEM SETTING : Description"
.
>> GO TO 3.
3.
MEMORY STORAGE
Perform memory storage. Refer to
ADP-8, "MEMORY STORING : Description"
>> END
SYSTEM INITIALIZATION
SYSTEM INITIALIZATION : Description
INFOID:0000000003759062
Always perform the initialization when the battery terminal is disconnected or the driver seat control unit is
replaced.
The entry/exit assist function will not operate normally unless initialization is performed.
SYSTEM INITIALIZATION : Special Repair Requirement
INFOID:0000000003759063
INITIALIZATION PROCEDURE
1.
CHOOSE METHOD
There are two initialization methods.
Which method do you use?
With door switch>>GO TO 2.
With vehicle speed>>GO TO 4.
2.
STEP A-1
Turn ignition switch from the ACC to the OFF position.
>> GO TO 3.
3.
STEP A-2
Driver door switch is ON (open)
→
OFF (close)
→
ON (open).
>> END
4.
STEP B-1
Drive the vehicle at more than 25 km/h (16 MPH).
>> END
MEMORY STORING
MEMORY STORING : Description
INFOID:0000000003759064
Always perform memory storage when the battery terminal is disconnected or the driver seat control unit is
replaced. The memory function and Intelligent Key interlock function will not operate normally unless memory
storage is performed.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст