Nissan Teana J32. Instruction — part 656
HA-52
< ON-VEHICLE REPAIR >
EVAPORATOR
EVAPORATOR
Exploded View
INFOID:0000000003825218
1.
Ventilator seal
2.
Defroster seal
3.
Distributor upper case
4.
Center case
5.
Heater & cooling unit case cover
6.
Foot duct 1 (right)
7.
Foot duct 2 (right)
8.
Air mix door motor (passenger side)
9.
Evaporator pipe assembly
10. Expansion valve
11.
O-ring
12.
Evaporator
13. Filter cover
14.
Air conditioner filter
15.
Case packing
16. Heater & cooling unit case (right)
17.
Cooler pipe grommet
18.
Grommet
19. Heater pipe grommet
20.
Heater pipe support
21.
Drain hose
22. Heater & cooling unit case (left)
23.
Air mix door motor (driver side)
24.
Heater core
25. Heater pipe cover
26.
Foot duct 2 (left)
27.
Foot duct 1 (left)
28. Aspirator hose
29.
Aspirator
30.
Mode door motor
31. Main link
32.
Rod link
33.
Ventilator door link
34. Mode door lever
35.
Ventilator door lever
36.
Max. cool door link
JPIIA0906GB
EVAPORATOR
HA-53
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
Removal and Installation
INFOID:0000000003795855
REMOVAL
1.
Remove evaporator pipe assembly. Refer to
.
2.
Slide evaporator (1) toward the right side of the vehicle (as
shown in the figure), and then remove intake sensor (2) from
evaporator.
3.
Remove evaporator.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
• Replace O-rings with new ones. Then apply compressor oil to them when installing.
• Mark the mounting position of intake sensor bracket prior to removal so that the reinstalled sensor
can be located in the same position.
• Do not rotate the bracket insertion part when removing and installing the intake sensor.
• Check for refrigerant leakage when charging refrigerant.
37.
Defroster door link
38.
Foot door link
39. Max. cool door lever
40.
Foot door lever
41.
Defroster door lever
42. Adapter case
43.
Distributor lower case
44.
Ventilator door
45. Intake sensor
46.
Intake sensor bracket
47.
Foot door
48. Max. cool door
49.
Defroster door
50.
Air mix door (Slide door)
Refer to
for symbols in the figure.
JPIIA0907ZZ
HA-54
< ON-VEHICLE REPAIR >
EVAPORATOR PIPE ASSEMBLY
EVAPORATOR PIPE ASSEMBLY
Exploded View
INFOID:0000000003825219
1.
Ventilator seal
2.
Defroster seal
3.
Distributor upper case
4.
Center case
5.
Heater & cooling unit case cover
6.
Foot duct 1 (right)
7.
Foot duct 2 (right)
8.
Air mix door motor (passenger side)
9.
Evaporator pipe assembly
10. Expansion valve
11.
O-ring
12.
Evaporator
13. Filter cover
14.
Air conditioner filter
15.
Case packing
16. Heater & cooling unit case (right)
17.
Cooler pipe grommet
18.
Grommet
19. Heater pipe grommet
20.
Heater pipe support
21.
Drain hose
22. Heater & cooling unit case (left)
23.
Air mix door motor (driver side)
24.
Heater core
25. Heater pipe cover
26.
Foot duct 2 (left)
27.
Foot duct 1 (left)
28. Aspirator hose
29.
Aspirator
30.
Mode door motor
31. Main link
32.
Rod link
33.
Ventilator door link
34. Mode door lever
35.
Ventilator door lever
36.
Max. cool door link
JPIIA0906GB
EVAPORATOR PIPE ASSEMBLY
HA-55
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
Removal and Installation
INFOID:0000000003795853
REMOVAL
1.
Disconnect the battery cable from the negative terminal after setting the temperature (passenger side) to
18
°
C (60
°
F).
2.
Use refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant.
3.
Remove mounting bolt (A), and then disconnect low-pressure
pipe (1) and high-pressure pipe (2) from expansion valve.
CAUTION:
Cap or wrap the joint of the A/C piping and expansion valve
with suitable material such as vinyl tape to avoid the entry
of air.
4.
Remove blower unit. Refer to the following.
•
(WITHOUT 7 INCH DISPLAY)
•
(WITH 7 INCH DISPLAY)
5.
Remove foot duct (right). Refer to the following.
•
VTL-59, "FOOT DUCT : Exploded View"
(WITHOUT 7 INCH DISPLAY)
•
VTL-117, "FOOT DUCT : Exploded View"
(WITH 7 INCH DISPLAY)
6.
Disconnect air mix door motor (passenger side) connector.
7.
Remove mounting screws (A), and then remove heater & cool-
ing unit case cover (1) with air mix door motor (passenger side)
(2) attached.
8.
Remove mounting bolts (A), and then remove evaporator pipe
assembly (1) from evaporator with expansion valve (2) attached.
CAUTION:
Cap or wrap the joint of the A/C piping and evaporator with
suitable material such as vinyl tape to avoid the entry of air.
37.
Defroster door link
38.
Foot door link
39. Max. cool door lever
40.
Foot door lever
41.
Defroster door lever
42. Adapter case
43.
Distributor lower case
44.
Ventilator door
45. Intake sensor
46.
Intake sensor bracket
47.
Foot door
48. Max. cool door
49.
Defroster door
50.
Air mix door (Slide door)
Refer to
for symbols in the figure.
JPIIA0915ZZ
JPIIA0563ZZ
JPIIA0546ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст